 Is This Going To Be A Problem, Valve Damage? *NEW PHOTOS, COMMENTS RQSTD* |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| kconway |
 Jun 3 2008, 07:25 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,347 Joined: 6-December 04 From: Monrovia, CA Member No.: 3,231 Region Association: Southern California  |
I'm changing out the pushrod tubes and seals and found this. Do I need to replace this valve?
Kev  |
   |
 
|
Posts in this topic
kconway Is This Going To Be A Problem Jun 3 2008, 07:25 PM
BarberDave :trophy:
Absolutely...... YES......... Dav... Jun 3 2008, 07:33 PM Phoenix 914-6GT Yes. You want it to be a nice smooth flat surface. Jun 3 2008, 07:34 PM BarberDave :trophy:
\
All of them ........ Dave :stoo... Jun 3 2008, 07:38 PM SLITS To save the valve, you could have the tip machined... Jun 3 2008, 07:39 PM BarberDave :trophy:
I would throw away all of them and the r... Jun 3 2008, 07:44 PM BarberDave SLIT"S Wouldn' t machineing the valve... Jun 3 2008, 07:48 PM
SLITS
SLIT"S Wouldn' t machineing the valv... Jun 3 2008, 09:14 PM kconway Can someone explain to me what the likely cause is... Jun 3 2008, 07:49 PM ericread Nah, You can buff that out. :rotfl: Jun 3 2008, 08:56 PM Headrage
Can I take the whole head to RIMCO
Yes Jun 3 2008, 10:53 PM brer You can get it done right here in san diego. Bet... Jun 3 2008, 11:17 PM kconway
You can get it done right here in san diego. Be... Jun 3 2008, 11:20 PM brer
You can get it done right here in san diego. B... Jun 3 2008, 11:49 PM sean_v8_914 if the engine is assembled and still in the car...... Jun 3 2008, 11:21 PM kconway
if the engine is assembled and still in the car..... Jun 3 2008, 11:22 PM Jake Raby Brer,
I never knew that was the "don" yo... Jun 3 2008, 11:54 PM brer
Brer,
I never knew that was the "don" y... Jun 4 2008, 10:49 AM HAM Inc Yep, loose valve adjustment, and or poor oil. Swiv... Jun 4 2008, 08:09 AM sean_v8_914 yup, bandaids have their place. I'm a "do... Jun 4 2008, 11:24 AM kconway Pulled the head off the one side...both exhaust va... Jun 4 2008, 08:55 PM (*)(*) Dude, you need to pull the valves, look for damage... Jun 4 2008, 10:34 PM (*)(*)
Dude, you need to pull the valves, look for damag... Jun 6 2008, 09:41 AM brer RIMCO will not be here long anyway.
fixtures and m... Jun 6 2008, 10:22 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 29th May 2024 - 06:05 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.