 Need help! Exhaust stud removal., Got that sumbiatch out!! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| KaptKaos |
  Jan 2 2009, 06:31 PM
Post
#1
|
|
Family  Group: Members Posts: 4,009 Joined: 23-April 03 From: Near Wausau Member No.: 607 Region Association: Upper MidWest  |
I snapped the top off of an exhaust stud a few days ago. There is thread left, but not too much. I have tried to double-nut it out, but there isn't enough engagement to get 2 nuts lined up and tight.
I tried some red lock-tite, and let it sit on a nut on the stud, but it came right off. I need some tips or tricks to getting that stud out. TIA |
   |
 
|
Posts in this topic
KaptKaos Need help! Exhaust stud removal. Jan 2 2009, 06:31 PM
dkjens Is the engine still in the car and runs? If so, ru... Jan 2 2009, 06:40 PM Vacca Rabite On a stud that I had a bitch of a time getting out... Jan 2 2009, 06:57 PM jim912928 I had to remove some where double nutting didn... Jan 2 2009, 07:46 PM Krieger914 Heat is good. Then take a hammer and a punch and ... Jan 2 2009, 08:32 PM Mikey914 I have felt your pain. I put a nut on mine and had... Jan 2 2009, 08:41 PM iamchappy One trick to try is Heat and paraffin wax. The wax... Jan 2 2009, 08:54 PM dinomium I now vote for the weld a bolt over the AutoZone e... Jan 3 2009, 12:27 AM Gint Drill, tap, timesert.
Search 914world for "t... Jan 3 2009, 07:23 AM KaptKaos I have tapped and used step down studs when a hole... Jan 3 2009, 11:40 AM HAM Inc Those ex studs are a real PITA. Sometimes even old... Jan 3 2009, 11:41 AM KaptKaos PBlast is tough since the car is up on ramps. I... Jan 3 2009, 11:44 AM KaptKaos Anyone in SoCal have something like this:
http:/... Jan 3 2009, 02:24 PM
dinomium
Anyone in SoCal have something like this:
http:... Jan 3 2009, 04:45 PM Wilhelm Heat + Paraffin + http://www.harborfreight.com/cpi... Jan 3 2009, 05:58 PM KaptKaos How do you get the paraffin up there when the moto... Jan 3 2009, 07:14 PM KaptKaos The plot thickens.
Stevo lent me his MIG welder... Jan 12 2009, 09:01 PM FourBlades You probably have spatter sticking the wire to the... Jan 12 2009, 09:23 PM Wilhelm Unscrew the copper tip of the miggy where the wire... Jan 13 2009, 12:48 AM 24/7 911 Hi,
some of the guys over here had good results wi... Jan 13 2009, 01:10 AM KaptKaos :trophy: :trophy: :trophy: :trophy: :trophy: :trop... Jan 17 2009, 07:29 PM Aaron Cox So.... why were you crankin on your exhaust studs ... Jan 17 2009, 10:47 PM KaptKaos
So.... why were you crankin on your exhaust studs... Jan 17 2009, 11:39 PM messix
So.... why were you crankin on your exhaust stud... Jan 17 2009, 11:42 PM messix so on reassembly what should be used to keep the s... Jan 17 2009, 11:12 PM KaptKaos Copper coated. I think the stud was just shot. Jan 17 2009, 11:53 PM Aaron Cox Nice... i like my eurorace header....
now make a ... Jan 18 2009, 06:55 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd May 2024 - 10:48 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.