 Tips for removing shift rod from shift rod head?, BFH? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| wobbletop |
 Jun 20 2009, 07:28 PM
Post
#1
|
|
Member  Group: Members Posts: 382 Joined: 8-December 06 From: Ontario, Canada Member No.: 7,335 Region Association: Canada  |
Hi,
The plastic cover for my side shifter linkage is not installed. To install it, I need to separate the shift rod from the shift rod end. Separate #27 from #24 in this diagram... (IMG:http://www.pelicanparts.com/914/Parts/Pedals/shift_linkage_side_big.jpg) Any tips? I have the tapered screw out (#23), but the two pieces seem very tightly joined. I have searched, but most refer to the joint close to the firewall. Will I be able to replace the plastic cover with just this joint removed, or will I need to take off the firewall joint as well. Thanks, Walter |
   |
 
|
Posts in this topic
wobbletop Tips for removing shift rod from shift rod head? Jun 20 2009, 07:28 PM
r_towle tap part number 24 towards the rear of the car whi... Jun 20 2009, 07:35 PM jaxdream Help your self out and use a brass drift on the en... Jun 20 2009, 08:44 PM swl http://www.914world.com/bbs2/index.php?showtopic=7... Jun 20 2009, 09:29 PM dbgriffith75 Either I was very lucky or very ignorant, but when... Jun 21 2009, 07:12 AM
RobW
Either I was very lucky or very ignorant, but whe... Jun 21 2009, 07:49 AM RobW If the screw is out, there's nothing but dirt ... Jun 21 2009, 07:46 AM wobbletop I'm coming to the realization that the plastic... Jun 21 2009, 08:31 AM GeorgeRud Once the cone screw is out, you certainly could us... Jun 21 2009, 09:28 AM dbgriffith75 Just keep working at it with a penetrating oil (WD... Jun 21 2009, 09:31 AM Dr Evil You can use heat as well, but make sure the surfac... Jun 22 2009, 12:13 PM osvolant I am a 914 newbie- have been struggling with the s... Sep 27 2009, 09:47 AM wobbletop That's what I did. I was originally trying to ... Sep 27 2009, 10:41 AM Dr Evil If all else fails:
Disconnect the the rod at the ... Sep 27 2009, 02:38 PM osvolant Thanks, guys. I am going to try Wobbletop's t... Sep 27 2009, 04:55 PM Dr Evil I have replacement o-rings for the console if you ... Sep 27 2009, 06:10 PM osvolant I tried my best and still can't get the shift ... Oct 11 2009, 12:47 PM Dr Evil
I tried my best and still can't get the shift... Oct 12 2009, 07:23 PM McMark Don't drill the roll pin out. Just drain the ... Oct 12 2009, 12:52 PM ellisor3 I had the same problem, tried heat, lubricant and ... Oct 12 2009, 07:05 PM osvolant :trophy: Thanks to Dr. Evil and anyone else who su... Nov 6 2009, 05:41 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th June 2024 - 11:23 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.