 Guess the part - 914-6 hand throttle, 3 sets now ready, just finalizing the costs |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| bcheney |
 Sep 9 2012, 09:22 AM
Post
#61
|
|
Senior Member  Group: Members Posts: 1,341 Joined: 16-November 03 From: Orlando, FL Member No.: 1,348 Region Association: South East States  |
QUOTE(Mikey914 @ Jun 6 2012, 05:59 PM)  Reassembling your shifter with the shift rod Push the end cap over the front end of the push rod. Be sure that you have tightened all screws! Next to come - Installation at pedal assembly Mikey, Can you post the next set of instructions? |
   |
 
|
| DEC |
Sep 10 2012, 01:37 AM
Post
#62
|
|
Senior Member Group: Members Posts: 632 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany 
|
Here the whole installation guide.
How_to_install_the_Handgas_lever.pdf ( 2.5mb )
Number of downloads: 553 |
|
|
|
| bcheney |
Sep 10 2012, 08:07 AM
Post
#63
|
|
Senior Member Group: Members Posts: 1,341 Joined: 16-November 03 From: Orlando, FL Member No.: 1,348 Region Association: South East States |
Thanks
|
|
|
|
| Mikey914 |
Dec 18 2012, 11:48 PM
Post
#64
|
|
The rubber man Group: Members Posts: 12,772 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
I have 2 more in. Who still wanted one. I know there was at least one of you out there, I just can't find my correspondence to figure out who it was?
|
|
|
|
| Peashooter |
Dec 19 2012, 12:14 PM
Post
#65
|
|
Member Group: Members Posts: 165 Joined: 17-December 11 From: SW Ohio Member No.: 13,903 Region Association: None |
PM'd you
|
 |
|
| Gint |
Dec 19 2012, 08:10 PM
Post
#66
|
|
Mike Ginter Group: Admin Posts: 16,096 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains  |
I want one, but I need to wait 6 weeks or so. You're going to run more aren't you Mark?
|
|
|
|
| Mikey914 |
Dec 20 2012, 12:37 AM
Post
#67
|
|
The rubber man Group: Members Posts: 12,772 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
I've been bringing these in from Germany. With the exchage rate on the Euro going up these may go up some. This a a batch I committed to back in Oct., so I got a good rate still. I'm not marking it up as my cost didn't go up, but I suspect they may be a little more this next round.
|
|
|
|
| gofor914 |
Jan 17 2013, 02:17 PM
Post
#68
|
|
Newbie Group: Members Posts: 2 Joined: 5-October 12 From: Belgium Member No.: 15,005 Region Association: Europe |
QUOTE(Mikey914 @ Dec 20 2012, 07:37 AM) I've been bringing these in from Germany. With the exchage rate on the Euro going up these may go up some. This a a batch I committed to back in Oct., so I got a good rate still. I'm not marking it up as my cost didn't go up, but I suspect they may be a little more this next round. I will buy a complet set hand throttle. I'm living in Europe. How can you help me? (IMG:style_emoticons/default/smile.gif) |
|
|
|
| DEC |
Jan 17 2013, 03:42 PM
Post
#69
|
|
Senior Member Group: Members Posts: 632 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany
|
PM sent
|
|
|
|
| jm993rs |
Jan 31 2013, 08:45 AM
Post
#70
|
|
Member Group: Members Posts: 68 Joined: 29-August 11 From: Mallorca Member No.: 13,498 Region Association: None |
Thank you guys !!
I need make the same operation in my car because I think I need for mount the 6 with MFI !! (IMG:style_emoticons/default/beer.gif) |
|
|
|
| DEC |
Jan 31 2013, 11:01 AM
Post
#71
|
|
Senior Member Group: Members Posts: 632 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany
|
I have one set left for the Europeans.
If anyone will have it let me know. I must check the interest to make a further run of these parts. |
|
|
|
| eric9144 |
Jan 31 2013, 12:42 PM
Post
#72
|
|
Advanced Member Group: Members Posts: 2,771 Joined: 30-March 11 From: San Diego, CA Member No.: 12,876 Region Association: Southern California
|
PM sent
|
|
|
|
| jm993rs |
Apr 17 2013, 05:15 AM
Post
#73
|
|
Member Group: Members Posts: 68 Joined: 29-August 11 From: Mallorca Member No.: 13,498 Region Association: None |
Thank you guys !!
Is good for me because I need for my conversion to engine 911 2.4 S !!!! |
|
|
|
| DEC |
Jul 18 2013, 06:40 AM
Post
#74
|
|
Senior Member Group: Members Posts: 632 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany
|
it works also for the MFI setup
|
|
|
|
| DEC |
Jul 18 2013, 06:45 AM
Post
#75
|
|
Senior Member Group: Members Posts: 632 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany
|
I have finished the last (all silver serie) run of 10 sets of the
914-6 hand throttle Please contact Mark/Mikey914 if you need one Europeans please PM me direct |
|
|
|
| Mikey914 |
Jul 18 2013, 08:18 AM
Post
#76
|
|
The rubber man Group: Members Posts: 12,772 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
I'm finally adding one to my carbed 4, looking forward to this run.
|
|
|
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd June 2025 - 10:48 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.