 int floor pictures, pretty damn clean and rust free |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rhodyguy |
 May 15 2003, 06:11 AM
Post
#1
|
|
Chimp Sanctuary NW. Check it out.  Group: Members Posts: 22,080 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch  |
the one closeup picture of the pass side is the only rust. its only surface in the seam. i'm taking the very nice org carpeting in and having it prof cleanned today.
kevin Attached image(s) 
|
   |
 
|
Posts in this topic
rhodyguy int floor pictures May 15 2003, 06:11 AM
rhodyguy two May 15 2003, 06:12 AM rhodyguy three May 15 2003, 06:13 AM rhodyguy four May 15 2003, 06:14 AM rhodyguy five May 15 2003, 06:15 AM Qarl Start prying up the tar...
SURPRISE! May 15 2003, 06:57 AM rhodyguy take up all the tar? are you crazy? i worried some... May 15 2003, 07:04 AM Bleyseng Nah....but I would then make you a t shirt that sa... May 15 2003, 07:40 AM Jeroen Don't be a wuss and remove the tar!
cheer... May 15 2003, 09:19 AM mskala <... May 15 2003, 10:09 AM Qarl Unfortunately I don't have any "before tar rem... May 15 2003, 10:20 AM Maine914 What is the best stuff to remove the tar with? May 15 2003, 10:29 AM Lawrence914-6 Heat gun, putty knife, patience.
Then a solvent t... May 15 2003, 10:34 AM Gint I think everyone has already said what I would hav... May 15 2003, 10:57 AM Jenny That's what I'll be doing this weekend. Is... May 15 2003, 11:03 AM Brad Roberts It takes 2 hours to pull the tar up with a heat gu... May 15 2003, 11:10 AM Jenny I guess by the end of this weekend I'll be wel... May 15 2003, 11:14 AM Qarl I wire brush wheel works good on the seam sealer. May 15 2003, 11:33 AM Gint Wear gloves May 15 2003, 11:34 AM SirAndy Jenny not as bad as getting herculiner on your hootus. ... May 15 2003, 11:36 AM Jeff Krieger Qarl heh heh heh heh! (insert evil laugh)
Guess yo... May 15 2003, 12:10 PM SirAndy this is how it looked before i took the tar out, n... May 15 2003, 12:12 PM Jeff Krieger <... May 15 2003, 12:26 PM rhodyguy i will think about this adventure NEXT winter. the... May 16 2003, 06:18 AM Gint QUOTE
Lawrence914-6 Cake.. rust.. what's the difference? ;-) May 16 2003, 09:16 AM stock93 I started taking the tar off of my 914 today. I pl... May 16 2003, 07:10 PM stock93 This is the after pic. I simply used a chisel sinc... May 16 2003, 07:11 PM Lawrence914-6 Hi John,
If I didn't say so already... welcom... May 16 2003, 07:14 PM stock93 Thanks for the welcome. I havent taken the tar off... May 16 2003, 07:19 PM Gint Welcome to the board John.
Andy,
<... May 16 2003, 10:32 PM stock93 Does anyone know what guage sheetmetal the floorpa... May 17 2003, 10:13 AM Jeff Krieger <... May 17 2003, 08:18 PM Russ K So do floor pans usually rust from the inside out?... May 17 2003, 11:39 PM
SirAndy   |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th May 2024 - 11:54 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.