Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> anyone ever PLATE a-arms or trailing arms ?
jimkelly
post Dec 2 2012, 12:18 PM
Post #1


Delaware USA
****

Group: Members
Posts: 4,969
Joined: 5-August 04
From: Delaware, USA
Member No.: 2,460
Region Association: MidAtlantic Region



pic


Attached image(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
Reply to this topicStart new topic
Replies
Eric_Shea
post Dec 2 2012, 09:33 PM
Post #2


PMB Performance
***************

Group: Admin
Posts: 19,274
Joined: 3-September 03
From: Salt Lake City, UT
Member No.: 1,110
Region Association: Rocky Mountains



We don't do either anymore. Zero-Rust on bare metal then a semi-gloss finish over that. Powder is too thick for brake clips and, the base as the arms fit into the crossbar.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rwilner
post Dec 3 2012, 10:16 AM
Post #3


No Ghosts in the Machine
***

Group: Members
Posts: 953
Joined: 30-March 10
From: Boston, MA
Member No.: 11,530
Region Association: North East States



QUOTE(Eric_Shea @ Dec 2 2012, 10:33 PM) *

We don't do either anymore. Zero-Rust on bare metal then a semi-gloss finish over that. Powder is too thick for brake clips and, the base as the arms fit into the crossbar.


+1
I had my A arms powder coated and cleared. I had to sand at least the clear away, being very careful not to expose bare metal, to get the ball joints to seat. Also, getting the sway bar bushings in was hard.

Plus -- Powder can't be touched-up if you ever want to, it needs to be blasted and coated all over again.

If I had to do it again, I'd get them blasted at a job shop and then paint them in my attic...or maybe take the $$ I would spend getting them powdercoated and buy myself a blast it all!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
r_towle
post Dec 3 2012, 11:47 AM
Post #4


Custom Member
***************

Group: Members
Posts: 24,573
Joined: 9-January 03
From: Taxachusetts
Member No.: 124
Region Association: North East States



QUOTE(rwilner @ Dec 3 2012, 11:16 AM) *

QUOTE(Eric_Shea @ Dec 2 2012, 10:33 PM) *

We don't do either anymore. Zero-Rust on bare metal then a semi-gloss finish over that. Powder is too thick for brake clips and, the base as the arms fit into the crossbar.


+1
I had my A arms powder coated and cleared. I had to sand at least the clear away, being very careful not to expose bare metal, to get the ball joints to seat. Also, getting the sway bar bushings in was hard.

Plus -- Powder can't be touched-up if you ever want to, it needs to be blasted and coated all over again.

If I had to do it again, I'd get them blasted at a job shop and then paint them in my attic...or maybe take the $$ I would spend getting them powdercoated and buy myself a blast it all!


Rich,

Feel free to come over and use a large cabinet with a large compressor.
You can stand there all day long and have fun.
Not my favortie thing to do with my time.

I send my stuff out in large batches...it comes back all done.
Send junk, get back pretty painted or powder coated stuff.

Never thought of plating suspension parts, but now that I see them, its not a bad idea.
I wonder if there is a way to plate them black...not so shiny...

Rich
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rwilner
post Dec 3 2012, 11:57 AM
Post #5


No Ghosts in the Machine
***

Group: Members
Posts: 953
Joined: 30-March 10
From: Boston, MA
Member No.: 11,530
Region Association: North East States



QUOTE(r_towle @ Dec 3 2012, 12:47 PM) *

I wonder if there is a way to plate them black...not so shiny...


There sure is...zinc nickel. It comes back looking like anodized aluminum. We had it done frequently for marine applications at my first job. The cool thing is that it's still electrically conductive, so you can use the coated parts to ground things to engine blocks.

[HIJACK] Rich, you should see my garage right now. Suspension and brake parts everywhere. After I work, I have to clear a path so Abbie can get the stroller in and out.
[/HIJACK]
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
r_towle
post Dec 3 2012, 12:07 PM
Post #6


Custom Member
***************

Group: Members
Posts: 24,573
Joined: 9-January 03
From: Taxachusetts
Member No.: 124
Region Association: North East States



QUOTE(rwilner @ Dec 3 2012, 12:57 PM) *

QUOTE(r_towle @ Dec 3 2012, 12:47 PM) *

I wonder if there is a way to plate them black...not so shiny...


There sure is...zinc nickel. It comes back looking like anodized aluminum. We had it done frequently for marine applications at my first job. The cool thing is that it's still electrically conductive, so you can use the coated parts to ground things to engine blocks.

[HIJACK] Rich, you should see my garage right now. Suspension and brake parts everywhere. After I work, I have to clear a path so Abbie can get the stroller in and out.
[/HIJACK]


Box up what you want and bring some or your favorite media and have at it.
Its all hooked up, vacuum system, lights and compressor.

Again, not my favorite place to stand all day long....

You do know that Home Depot sells big ass plastic shelving units....right?

Get some 2*4,s and plywood, build a shelf over the front hood of the car.
Put all your shit on there, get it out of the mad angry mom's way.

Big ass plywood shelf/floor
Built for weight....post under shelf, dont rely on the shear strength of a nail.
Then, get the plastic shelves from Home depot and set them up there in half sections.
You get about 4 feet of storage...double depth if you do it right.
Everything (everything) but the engine can fit on top of a porsche....with proper shelving and roof racks (IMG:style_emoticons/default/smile.gif)

If you are an engineer, you can also put the motor above the car...but you need to lift it...and you have room in front of the car for that...so I would not bother.
Get her car inside dufus.

rich

rich
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
biosurfer1
post Apr 16 2014, 09:02 PM
Post #7


Teener fo Life!
****

Group: Members
Posts: 3,020
Joined: 3-August 03
From: Roseville, CA
Member No.: 977
Region Association: Northern California



QUOTE(r_towle @ Dec 3 2012, 11:07 AM) *



You do know that Home Depot sells big ass plastic shelving units....right?

Get some 2*4,s and plywood, build a shelf over the front hood of the car.
Put all your shit on there, get it out of the mad angry mom's way.



That is brilliant Rich! I know what I'll be making this weekend. The space above my 914 in the garage is wasted right now (IMG:style_emoticons/default/beer.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MoveQik
post Apr 17 2014, 06:24 AM
Post #8


What size wheels can I fit?
****

Group: Members
Posts: 4,645
Joined: 5-April 05
From: Scottsdale, AZ
Member No.: 3,881
Region Association: Southwest Region



QUOTE(biosurfer1 @ Apr 16 2014, 08:02 PM) *

QUOTE(r_towle @ Dec 3 2012, 11:07 AM) *



You do know that Home Depot sells big ass plastic shelving units....right?

Get some 2*4,s and plywood, build a shelf over the front hood of the car.
Put all your shit on there, get it out of the mad angry mom's way.



That is brilliant Rich! I know what I'll be making this weekend. The space above my 914 in the garage is wasted right now (IMG:style_emoticons/default/beer.gif)

Slight hijack...I have a similar solution. I put two of the steel shelving units together so the shelf is 3' deep and the car fits perfectly. (IMG:style_emoticons/default/biggrin.gif)


Attached thumbnail(s)
Attached Image

Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic
jimkelly   anyone ever PLATE a-arms or trailing arms ?   Dec 2 2012, 12:18 PM
G e o r g e   pic like this   Dec 2 2012, 12:21 PM
euro911   Those look Sharp :rolleyes:   Dec 2 2012, 01:10 PM
G e o r g e   Those look Sharp :rolleyes: Don't They... ...   Dec 2 2012, 02:25 PM
Rand   Why?   Dec 2 2012, 01:34 PM
echocanyons   I would think powder coating would be a bit more i...   Dec 2 2012, 01:36 PM
Rand   Is this discussion about bling factor? It's no...   Dec 2 2012, 01:39 PM
Rand   Don't stop at zinc. Go for gold.   Dec 2 2012, 01:41 PM
jimkelly   i've asked from the standpoint of - not bling ...   Dec 2 2012, 03:10 PM
Rand   i've asked from the standpoint of - not bling...   Dec 2 2012, 05:38 PM
monkeyboy   I would probably powder coat it myself, but those ...   Dec 2 2012, 08:17 PM
Eric_Shea   We don't do either anymore. Zero-Rust on bare...   Dec 2 2012, 09:33 PM
rwilner   We don't do either anymore. Zero-Rust on bar...   Dec 3 2012, 10:16 AM
r_towle   We don't do either anymore. Zero-Rust on ba...   Dec 3 2012, 11:47 AM
rwilner   I wonder if there is a way to plate them black......   Dec 3 2012, 11:57 AM
r_towle   I wonder if there is a way to plate them black.....   Dec 3 2012, 12:07 PM
biosurfer1   You do know that Home Depot sells big ass plast...   Apr 16 2014, 09:02 PM
MoveQik   You do know that Home Depot sells big ass plas...   Apr 17 2014, 06:24 AM
wndsnd   [quote name='rwilner' post='1777631' date='Dec 3 ...   Apr 17 2014, 04:51 PM
Joe Sharp   Those parts went on Carerror, so far only used as ...   Dec 3 2012, 07:39 AM
bshounen   on the subject of arms lets talk about mak'n t...   Apr 16 2014, 08:56 PM
CptTripps   I wish I had just painted my A and Trailing arms. ...   Apr 17 2014, 07:29 AM
porschetub   I wish I had just painted my A and Trailing arms....   Jun 19 2017, 03:14 PM
914 Ranch   When I had the parts plated all I had to do is pac...   Jun 19 2017, 08:44 AM


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 5th May 2024 - 04:09 PM