 Group buy aircleaner-to-throttle body seal rubber sleve, $10.20 these will be $16.80 after |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Mikey914 |
 Mar 6 2014, 01:56 AM
Post
#1
|
|
The rubber man  Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None 
 |
I was tapped to make these and both of my cars need them. So I set out to make them. These will be ready in 2 weeks. Who needs them?
I even have the clamp ridge molded in. Attached thumbnail(s)  Attached image(s) 
|
   |
 
|
| Olympic 914 |
Mar 6 2014, 07:48 AM
Post
#2
|
|
Group: Members Posts: 1,662 Joined: 7-July 11 From: Pittsburgh PA Member No.: 13,287 Region Association: North East States
|
I'm in for two.
Thanks Mark |
|
|
|
| timothy_nd28 |
Mar 6 2014, 07:51 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,299 Joined: 25-September 07 From: IN Member No.: 8,154 Region Association: Upper MidWest
|
You have anything for the 1.8l crowd?
|
|
|
|
| DRPHIL914 |
Mar 6 2014, 08:35 AM
Post
#4
|
|
Dr. Phil Group: Members Posts: 5,766 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States
|
i'll take one for my 2.0
|
|
|
|
| rnellums |
Mar 6 2014, 08:44 AM
Post
#5
|
|
Professional Enthusiast Group: Members Posts: 1,646 Joined: 26-November 09 From: Littleton, CO Member No.: 11,072 Region Association: Rocky Mountains |
I would like one
|
|
|
|
| Cap'n Krusty |
Mar 6 2014, 09:16 AM
Post
#6
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
That thing looks suspiciously like the aircleaner-to-throttle body seal. The throttle body-to-plenum seal is a thick flat paper gasket. Might wanna change the title of your thread to accurately reflect the correct product application.
The Cap'n |
|
|
|
| Mikey914 |
Mar 6 2014, 12:20 PM
Post
#7
|
|
The rubber man Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
Edited for clarification thanks Crusty!
I also had the wrong part number |
|
|
|
| Mikey914 |
Mar 6 2014, 12:21 PM
Post
#8
|
|
The rubber man Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
QUOTE(timothy_nd28 @ Mar 6 2014, 05:51 AM)  You have anything for the 1.8l crowd? It's possible. That one is a bit more complicated. but if it's needed and there is enough demand to pay for it, I'm sure I can. -Mark |
|
|
|
| usros |
Mar 28 2014, 05:51 PM
Post
#9
|
|
Newbie Group: Members Posts: 11 Joined: 29-August 04 From: Malvern, Oh Member No.: 2,647 Region Association: None |
I need one also. Let me know when they are available
|
|
|
|
| brant |
Mar 28 2014, 08:44 PM
Post
#10
|
|
914 Wizard Group: Members Posts: 11,618 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
are the 1.7 and 2.0 the same?
I assume they are I need one for a 2.0 please brant |
 |
|
| Mikey914 |
Mar 29 2014, 11:12 AM
Post
#11
|
|
The rubber man Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
I'm actually done and have these in stock. I have a few other items I've been holding them off for so you guys could include more in your group buys and combine instead of having a bunch of shipping for each part.
I'll get this and the other up on Monday. Stay tuned.... |
|
|
|
| Mikey914 |
Mar 29 2014, 05:06 PM
Post
#12
|
|
The rubber man Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
QUOTE(Mikey914 @ Mar 29 2014, 10:12 AM) I'm actually done and have these in stock. I have a few other items I've been holding them off for so you guys could include more in your group buys and combine instead of having a bunch of shipping for each part. I'll get this and the other up on Monday. Stay tuned.... I pic of a few finished parts- Attached thumbnail(s) 
|
|
|
|
| Robert21 |
Mar 29 2014, 07:50 PM
Post
#13
|
|
ron21 Group: Members Posts: 288 Joined: 9-July 04 From: Seal Beach Ca 90630 Orange co Member No.: 2,330 Region Association: None
|
I will buy one , thanks
|
|
|
|
| Mikey914 |
Apr 2 2014, 12:05 PM
Post
#14
|
|
The rubber man Group: Members Posts: 12,649 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
PM's sent to all
Thanks |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd May 2024 - 02:16 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.