Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> My Frame Repair Project, Warning - Rust Content
cdmcse
post Feb 13 2005, 12:15 AM
Post #1


Member
**

Group: Members
Posts: 340
Joined: 17-December 04
From: Georgetown, Ky
Member No.: 3,305
It seemed like it was going to take forever to make some progress on my rust repair. After spending the entire winter locating parts, grinding, cuting, painting, and learning to weld, I was finally ready to take the plunge....

Also thanks to everyone on the board, I would have never had enough confidence to tackle this without this site!!!

BTW: I must be getting addicted to the "914 lifestyle" as I had withdrawal when the site was down. (IMG:http://www.914world.com/bbs2/html/emoticons/happy11.gif)

Fist Pic : The Rust


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Posts in this topic
cdmcse   My Frame Repair Project   Feb 13 2005, 12:15 AM
cdmcse   Where the motor mount was.   Feb 13 2005, 12:15 AM
cdmcse   Here we go.   Feb 13 2005, 12:17 AM
cdmcse   The repair piece from a parts car.   Feb 13 2005, 12:18 AM
cdmcse   Clamped.   Feb 13 2005, 12:19 AM
cdmcse   Welded (no making fun) http://www....   Feb 13 2005, 12:20 AM
cdmcse   The patch for the frame under the engine mount.   Feb 13 2005, 12:21 AM
cdmcse   Patch welded in.   Feb 13 2005, 12:22 AM
cdmcse   This part is next, after a little clean up in the ...   Feb 13 2005, 12:23 AM
Lou W   Looks great, keep the pictures coming. I'm get...   Feb 13 2005, 01:30 AM
Bleyseng   Whats with the electrical cable coming out of the ...   Feb 13 2005, 09:41 AM
jd74914   looks good http://www.914worl...   Feb 13 2005, 10:10 AM
cdmcse   These cables in the heater tubes are for a front t...   Feb 13 2005, 11:25 AM
cdmcse   Motor Mount is in, I can practially hear the engin...   Feb 13 2005, 07:24 PM
mharrison   You don't need a floor pan to run the engine...   Feb 13 2005, 08:13 PM
MecGen   Thumbs up Dude http://ww...   Feb 13 2005, 09:08 PM
cdmcse   Made some more progress Before:   Feb 23 2005, 11:40 PM
cdmcse   After:   Feb 23 2005, 11:42 PM
cdmcse   Outer Firewall back in:   Feb 23 2005, 11:43 PM
SirAndy   did you spray plenty of "metal-ready" inside that ...   Feb 23 2005, 11:57 PM
cdmcse   Yep, I metal readied the hell out of it it. Then I...   Feb 24 2005, 12:09 AM
Jamie   Looks like you're making great progress. We ne...   Feb 25 2005, 08:58 PM
MecGen   Hello I just spoke with the dist of Por15, for alm...   Feb 26 2005, 07:31 AM
cdmcse   Well, with POR-15 I've noticed that the prep i...   Feb 26 2005, 10:42 AM
red914   WOW! you have done imipressive work. i see m...   Feb 26 2005, 10:47 AM
cdmcse   Jamie, Another teener, cool. Including yours and ...   Feb 26 2005, 11:25 AM
cdmcse   Ok I made some more progress this weekend. I got t...   Feb 27 2005, 11:36 PM
cdmcse   The new pan...   Feb 27 2005, 11:37 PM
cdmcse   Zee Hole...   Feb 27 2005, 11:39 PM
cdmcse   Zee other hole...   Feb 27 2005, 11:39 PM
cdmcse   Who wants to see down my tunnel?   Feb 27 2005, 11:40 PM
cdmcse   The firewall side of the tunnel...   Feb 27 2005, 11:42 PM
cdmcse   Up the firewall on the driver's side...   Feb 27 2005, 11:42 PM
cdmcse   Broken clutch tube support about half way down the...   Feb 27 2005, 11:48 PM
cdmcse   Broken tube at the firewall...   Feb 27 2005, 11:49 PM
cdmcse   Look, I made some cash while tearing out the floor...   Feb 27 2005, 11:51 PM
cdmcse   Forgot the pic.   Feb 27 2005, 11:52 PM
cdmcse   Why you should always wear your safety gear. This...   Feb 27 2005, 11:55 PM
Lou W     Mar 1 2005, 12:09 AM
Travis Neff   Never too many pics, NEVER!   Mar 1 2005, 10:45 AM
cdmcse   I welded all the clutch tube breakage, then I adde...   Mar 2 2005, 01:54 AM
cdmcse   New metal fuel lines secured to the center of the ...   Mar 2 2005, 01:55 AM
cdmcse   Fuel Tank end   Mar 2 2005, 01:56 AM
cdmcse   Firewall End.   Mar 2 2005, 01:56 AM
cdmcse   POR-15 Applied. Is there anything else I should d...   Mar 2 2005, 01:58 AM
Jeroen   I see light at the end of your tunnel http://www.914world.com/bbs...   Mar 2 2005, 06:52 PM
cdmcse   mr914, If you are ready to get started on the repa...   Mar 2 2005, 08:50 PM
cdmcse   OK, more progress...Top coated the POR-15 with som...   Mar 4 2005, 01:22 AM
cdmcse   http://www.914world.com/bbs2/...   Mar 4 2005, 01:23 AM
cdmcse   Driver's Side.   Mar 4 2005, 01:24 AM
cdmcse   Passenger Side. Next I have to finish the passenge...   Mar 4 2005, 01:26 AM
Jeroen   Impressive job! Go have a   Mar 15 2005, 01:19 AM
SpecialK   Now that's a view of the center tunnel you don...   Mar 15 2005, 03:07 AM
Lou W   Looks great http://www.914wo...   Mar 15 2005, 11:41 AM
Travis Neff   That's love buddy, painting to match on the in...   Mar 15 2005, 11:49 AM
Gint   Good lookin work!   Mar 15 2005, 01:02 PM
cdmcse   Well, after the arrival of our new son (March 6th)...   Apr 4 2005, 10:52 PM
cdmcse   Now back on topic...Passenger side floor re-enforc...   Apr 4 2005, 10:54 PM
cdmcse   Driver's side floor re-enforcement, this one i...   Apr 4 2005, 10:56 PM
cdmcse   Right Rear Floor Jackpoint.   Apr 4 2005, 10:56 PM
cdmcse   Left Rear Jackpoint.   Apr 4 2005, 10:57 PM
cdmcse   Engine Shelf installed. I finally got all the part...   Apr 4 2005, 10:58 PM
cdmcse   The interior all grinded and stripped ready to POR...   Apr 4 2005, 10:59 PM
cdmcse   The Firewall had Zero Rust!!!! Yay...   Apr 4 2005, 11:01 PM
michelko   Fantastic http://www.914worl...   Apr 5 2005, 12:20 AM
Jeroen   Excellent work Chris! And congrats on the kid ...   Apr 5 2005, 06:00 AM
CptTripps   Well done sir....very nice work. I think we need ...   Apr 5 2005, 07:07 AM
kafermeister   Wow! congrats on the new arrival. You know i...   Apr 5 2005, 07:28 AM
Gint   Congratulations on the pit crew!   Apr 5 2005, 07:38 AM
cdmcse   A little farther along... POR-15 Silver Applied   Apr 7 2005, 11:08 PM
cdmcse   Another...   Apr 7 2005, 11:10 PM
Root_Werks   Sweet! Another 914 saved from the rust monste...   Apr 8 2005, 08:44 AM
maf914   Way to go, Chris! Great looking work. Also...   Apr 8 2005, 11:17 AM
cdmcse   Well I reached what I feel like is a major milesto...   Apr 12 2005, 09:44 PM
cdmcse   Another...   Apr 12 2005, 09:45 PM
cdmcse   Another   Apr 12 2005, 09:46 PM
cdmcse   Last one. Now just a few more bits on the outside ...   Apr 12 2005, 09:47 PM
dakotaewing   How did you apply the Por-15 and primer? Gun or br...   Apr 12 2005, 09:52 PM
cdmcse   http://www.914world.com/b...   Apr 13 2005, 09:16 AM
Gint   That does look fantastic. Nice work.   Apr 13 2005, 10:08 AM
dakotaewing     Apr 13 2005, 12:46 PM
cdmcse     Apr 14 2005, 12:24 AM
cdmcse   ...   Apr 14 2005, 12:58 AM
premierauto5150   Chris...I just have to throw in my two cents here....   Apr 21 2005, 11:19 AM
Bleyseng   Oh, you mean the one in your avatar pic??? looks l...   Apr 21 2005, 12:45 PM
cdmcse  
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

- Lo-Fi Version Time is now: 20th May 2024 - 10:28 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...