 Muffler Options for T4 Header, Updated to SpinTech Muffler |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 7TPorsh |
 Jul 28 2015, 04:49 PM
Post
#1
|
|
7T Porsh  Group: Members Posts: 2,691 Joined: 27-March 06 From: Glendale Ca Member No.: 5,782 Region Association: Southern California 
 |
Working out installing a msds T4 header and am considering muffler options. My first choice was to attach a flowmaster to the end of the collector and add a tail pipe....header exits on the driver's side.
It is turning out there may not be enough room since the header collector and reducer put the flange out near the end of the trans. I can route the pipe and muffler across the back and exit the passenger's side but then I need to change my valance. I think curving the pipe back to the driver's side will be tight; and hard to find a shop to spend the time. I remember seeing some kind of 911 muffler, banana type, that had the inlet and exit on the same side. Was that a custom job? Are they effective? Has anyone done this setup? How do you mount the muffler? |
   |
 
|
Posts in this topic
7TPorsh Muffler Options for T4 Header Jul 28 2015, 04:49 PM
914forme
Working out installing a msds T4 header and am co... Jul 28 2015, 05:10 PM
era vulgaris
Tangerine Racing - EVO II silencer. Single inle... Jul 28 2015, 05:26 PM 7TPorsh Tangerine is way out of my budget. Was thinking an... Jul 28 2015, 07:27 PM 7TPorsh I am thinking of one of these? Anyone have one on... Jul 29 2015, 11:24 AM porschetub I don't see why not they are a pretty good des... Jul 29 2015, 04:37 PM aircooledtechguy I'm about a month away from firing mine up for... Jul 29 2015, 05:29 PM Chris914n6 I have the SC on my nissan vq30. Exits out the fac... Jul 30 2015, 01:38 AM 7TPorsh Here is what I am looking at...car is on ramps so ... Jul 30 2015, 10:17 AM Chris914n6 http://www.914world.com/bbs2/uploads_offsite/lh3.g... Jul 30 2015, 05:59 PM Dave_Darling Is that a rubber mount between the muffler and bod... Jul 31 2015, 09:00 AM Chris914n6 ^^ Yes. Technically a repurposed section from a ti... Jul 31 2015, 01:23 PM 7TPorsh So it is not hard connected? is all the weight on... Jul 31 2015, 02:34 PM Dave_Darling If it gets hard connected, it must be to the trans... Jul 31 2015, 03:26 PM Chris914n6 No weight on the studs, it's all supported by ... Jul 31 2015, 05:47 PM 7TPorsh I'm thinking to weld on a factory bracket and ... Jul 31 2015, 07:23 PM porschetub
I'm thinking to weld on a factory bracket and... Aug 1 2015, 11:38 PM 7TPorsh Well I have decided to go a different route. I am ... Aug 4 2015, 04:03 PM don-6 I have an 86 Carrera Muffler. PM sent. Aug 4 2015, 06:12 PM 7TPorsh WHat do you guys do with the clutch and speedo cab... Aug 7 2015, 11:28 AM Mark Henry
WHat do you guys do with the clutch and speedo ca... Jun 16 2017, 10:06 AM 7TPorsh
WHat do you guys do with the clutch and speedo ca... Aug 7 2015, 11:32 AM ThePaintedMan Look up "Clutch Pulley Adapter" on Chris... Aug 7 2015, 12:19 PM rhodyguy Also note Chris sells insulating sleeve material f... Aug 7 2015, 12:27 PM 914werke
I'm about a month away from firing mine up fo... Aug 7 2015, 01:06 PM 7TPorsh Lots of things to deal with when adding a header:
... Aug 14 2015, 12:36 PM 7TPorsh Welding day at the local muffler shop...the before... Sep 14 2015, 01:47 PM 7TPorsh Custom fit
Fire!!
Sep 14 2015, 01:51 PM 7TPorsh Nice Clean butt! ... and sounds really good... Sep 14 2015, 01:53 PM Chris H. Looks great! Sep 14 2015, 02:15 PM Dave_Darling If it's feasible, I would suggest supporting t... Sep 14 2015, 04:43 PM 7TPorsh
If it's feasible, I would suggest supporting ... Sep 15 2015, 09:24 AM 7TPorsh Also notice the Tangerine Racing piece to lower th... Sep 15 2015, 09:27 AM Maltese Falcon Excellent fabrication, he is a first class muffler... Sep 15 2015, 07:44 PM 7TPorsh Here's an update (sound of typewriters)....wha... Jun 16 2017, 08:57 AM Mark Henry Just did my e-brake cable with fire sleeve. :D
... Jun 16 2017, 04:01 PM Maltese Falcon Can't wait to see the finished product Gary...... Jun 16 2017, 10:06 PM 7TPorsh :bump: ing my thread to post an update.
After pla... Jul 26 2017, 09:55 AM Mueller ^Still enjoying that SpinTech muffler setup? :) Jan 3 2018, 10:54 AM 7TPorsh Oh yeah, I get nothing but compliments....everyone... Jan 3 2018, 12:40 PM Larmo63 Tangerine clutch pulley set-up with Patrick Motors... Jan 3 2018, 11:09 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd May 2024 - 04:34 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.