Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
Reply to this topicStart new topic
> Who has mounted Mikey’s Fender Liners?, 914 Rubber Issue
RickS
post Dec 2 2017, 10:28 PM
Post #1


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Just received the box with the liners. Instead of the stated “clips” for mounting they came with rivets. Clips suggest clipping the liners to the fenders or other attachment points rivets on the other hand... Am a bit hesitant to start drilling holes in my original sheet metal. No instructions were provided either.

Any one done this or have suggestions of the least invasive way they mounted these not using “clips”?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 2 2017, 11:24 PM
Post #2


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



The rivets go into the fender liner, not the car. You reuse the end bolts on the rocker panel and the rear valence.
Here's a shot .............

Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 3 2017, 12:36 AM
Post #3


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Thanks Cary. That makes total sense. Still have everything in the shipping box since I just got back to town tonight.

Don’t think quick some instructions would be too much to ask but this is pretty much a DIY site.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 3 2017, 01:05 AM
Post #4


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



Matt and I talked about it one night while putting his car together. But then we got busy.

Maybe I'll grab a set and install them on Doug's car for a demo. Black on primer should show up pretty well. Plus being on the rotisserie we'd be able get some great angles.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Dec 3 2017, 08:15 AM
Post #5


Bumpers, that's what I do!
***************

Group: Members
Posts: 16,253
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada



914rubber (and other member vendors) shouldn't have to included written instructions, but I'd suggest a web link addy to a how to thread here might be a good idea.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 4 2017, 01:52 AM
Post #6


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



QUOTE(Mark Henry @ Dec 3 2017, 06:15 AM) *

914rubber (and other member vendors) shouldn't have to included written instructions


Please tell me, based on what? Or do you ASSUME that because one can access this site they magically have the knowledge to perform all tasks on their cars flawlessly?That is one hell of a big assumption. You seem to forget that one of the premise behind this site is people helping people since most don’t posses said magic.

You are correct that vendors shouldn’t HAVE to include anything but the part, however many reputable vendors do, including JWest. A vendor which goes the extra mile for their customers tend to be the most successful. Not rocket science. I do agree with you that providing instructions on non-intuitive installs on their websites would work.

I have been buying quality reasonably priced parts from Mickey ever since he opened shop so if you feel the need to defend him, you can save your breath. I can’t count how many items I have bought from him through the years. Whenever there was an issue he stepped right up and resolved it. I will continue to buy parts from him with or without instructions but it doesn’t mean there isn’t always room for improvement. But what do I know after being a consultant to successful businesses for the last 25 years on how to grow and increase profitability, i could be wrong.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mikey914
post Dec 4 2017, 04:16 AM
Post #7


The rubber man
*****

Group: Members
Posts: 7,575
Joined: 27-December 04
From: Hillsboro, OR
Member No.: 3,348
Region Association: None



We are actually taking more steps to document installations and provide more instruction.
I totally get it. Cary has also been working with us to document some if the items.

It's part of the transition to adding more infer structure and allow us to help you.

Let me know if you need any more info, but looks like Cary is gonna drop you the short version. We will finalize them shortly.
Mark
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Dec 4 2017, 07:30 AM
Post #8


Bumpers, that's what I do!
***************

Group: Members
Posts: 16,253
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada



QUOTE(RickS @ Dec 4 2017, 02:52 AM) *

QUOTE(Mark Henry @ Dec 3 2017, 06:15 AM) *

914rubber (and other member vendors) shouldn't have to included written instructions


Please tell me, based on what? Or do you ASSUME that because one can access this site they magically have the knowledge to perform all tasks on their cars flawlessly?That is one hell of a big assumption. You seem to forget that one of the premise behind this site is people helping people since most don’t posses said magic.

You are correct that vendors shouldn’t HAVE to include anything but the part, however many reputable vendors do, including JWest. A vendor which goes the extra mile for their customers tend to be the most successful. Not rocket science. I do agree with you that providing instructions on non-intuitive installs on their websites would work.

I have been buying quality reasonably priced parts from Mickey ever since he opened shop so if you feel the need to defend him, you can save your breath. I can’t count how many items I have bought from him through the years. Whenever there was an issue he stepped right up and resolved it. I will continue to buy parts from him with or without instructions but it doesn’t mean there isn’t always room for improvement. But what do I know after being a consultant to successful businesses for the last 25 years on how to grow and increase profitability, i could be wrong.


Did you read the rest? I said a vendor just needs a link to a "how to" thread on this site.

You only know about 914rubber through the net, most likely from this site. So to me a "how to" thread would often be more in depth than any instruction sheet.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 7 2017, 12:13 AM
Post #9


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



Crash Course : The wide one goes it the back.

Step one, attach the mounts. The front I had the liner flush with the fender lip. The rear I had back up tight against the inner fender.
Attached Image

Attached Image

Now flex the liner into place.
Attached Image

Attached Image

Attached Image

Then bow the liner behind the mount to allow you to drill the 1/8" holes.
Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 7 2017, 12:32 AM
Post #10


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



Pretty simple. Drill the holes and rivet it in. Keep an eye on the location of the liner in the arch. It wants to slide up, and you want to keep it tight and tidy against the fender.
Attached Image

Front fender is more of the same.
Attached Image

Attached Image

Attached Image

Attached Image

These were installed without any trimming or tuning of the liner.

Every 914 needs these. 1. Protects the front fender to cowl joint. 2. Protects the seam sealer behind the door latch plate. 3. Keeps debris from getting slung into the jack point. 4. Most important, keeps debris and moisture getting slung up into the poorly designed joint under the sail panel inside the rear fender.







User is online!Profile CardPM
Go to the top of the page
+Quote Post
raynekat
post Dec 7 2017, 12:39 AM
Post #11


Senior Member
***

Group: Members
Posts: 701
Joined: 30-December 14
From: Portland, Oregon
Member No.: 18,263
Region Association: Pacific Northwest



Cary, guess you better sell me those liners.
Since they're set up for my car.
(IMG:style_emoticons/default/wink.gif)
(IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 7 2017, 12:42 AM
Post #12


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



All boxed up and ready to go .................... LOL
User is online!Profile CardPM
Go to the top of the page
+Quote Post
914forme
post Dec 7 2017, 10:22 AM
Post #13


Times a wastin', get wrenchin'!
****

Group: Members
Posts: 2,455
Joined: 24-July 04
From: Dayton, Ohio
Member No.: 2,388



QUOTE(cary @ Dec 7 2017, 01:32 AM) *



Every 914 needs these. 1. Protects the front fender to cowl joint. 2. Protects the seam sealer behind the door latch plate. 3. Keeps debris from getting slung into the jack point. 4. Most important, keeps debris and moisture getting slung up into the poorly designed joint under the sail panel inside the rear fender.

(IMG:style_emoticons/default/agree.gif)

And something else to purchase.

(IMG:style_emoticons/default/headbang.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 9 2017, 08:50 PM
Post #14


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Thanks Cory for all the valuable info. Is this a front or rear? I am guessing it is a front, but where does that little tab on the end go? It seems to interfere wherever it goes. The front of that piece is slightly notched for the fender but the tab is a mystery. Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 9 2017, 09:03 PM
Post #15


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Here is my misguided attempt to try to make the piece which matches the one above fit in the back of the front wheel well. I notched it but it still won’t snug up to the fender.
Attached Image
You can see the issue with that tongue piece.
When flush mounting the liners against the fender lips how can you access the bolts which mount the L brackets when you want to drop a valence or the rocker panel?

When trying to mount the driver rear piece, how did you work around the suspension pieces with the zirk fitting? Seemed to be a lot of interference due to the suspension.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 9 2017, 09:20 PM
Post #16


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Here is the clearance issue with mounting the rear There just doesn’t seem to be room to fit the liner with the bracket since it hits the suspension. Also how do you get to the zirk with the liner in place?
Attached Image

if the solution is to mount the L bracket on the inside, how do you access the bolt to remove the rocker without drilling out the rivers? I am repainting the rockers and was going to put them on last.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 9 2017, 11:50 PM
Post #17


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



QUOTE(RickS @ Dec 9 2017, 06:50 PM) *

Thanks Cory for all the valuable info. Is this a front or rear? I am guessing it is a front, but where does that little tab on the end go? It seems to interfere wherever it goes. The front of that piece is slightly notched for the fender but the tab is a mystery. Attached Image Attached Image


That's the rear.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 9 2017, 11:57 PM
Post #18


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



Here's the tab on the left rear. You can see the little tab / tongue right in front of the rear
trailing arm.
Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post
cary
post Dec 10 2017, 12:06 AM
Post #19


Advanced Member
****

Group: Members
Posts: 3,080
Joined: 26-January 04
From: Sherwood Oregon
Member No.: 1,608
Region Association: Pacific Northwest



QUOTE(RickS @ Dec 9 2017, 07:20 PM) *

Here is the clearance issue with mounting the rear There just doesn’t seem to be room to fit the liner with the bracket since it hits the suspension. Also how do you get to the zirk with the liner in place?
Attached Image

if the solution is to mount the L bracket on the inside, how do you access the bolt to remove the rocker without drilling out the rivers? I am repainting the rockers and was going to put them on last.


Drilling out the rivets will always be the easiest way out. 1/8" drill bit and they pop right off. I've always had the advantage of having the car up on a lift. Giving me more access.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
RickS
post Dec 10 2017, 12:37 AM
Post #20


Senior Member
***

Group: Members
Posts: 945
Joined: 17-April 06
From: 'False City', WA
Member No.: 5,880
Region Association: None



Thank you sir. Got it completely back-asswards. Much appreciated
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

2 Pages V  1 2 >
Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 13th December 2017 - 02:22 AM