 Member Vendor, Who was it that made these ? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jim_hoyland |
 Apr 22 2018, 08:32 AM
Post
#1
|
|
Get that VIN ?  Group: Members Posts: 9,278 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California 
 |
Years ago a 914World member made these and sold them in a group buy.
I’m trying to remember who that is ... Attached image(s) 
|
   |
 
|
  |
Replies
| Mikey914 |
Apr 23 2018, 10:14 AM
Post
#2
|
|
The rubber man Group: Members Posts: 12,659 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
I bought up a bunch of them and had plated to keep from rusting (the tie rod wrench) The problem I had was they were a little "soft" so I was not too happy about that. If McMark want to do up a run I'd be happy to distribute. i do have the tie rod one in stock $25.
-Mark |
|
|
|
| Rand |
Apr 23 2018, 01:36 PM
Post
#3
|
|
Cross Member Group: Members Posts: 7,409 Joined: 8-February 05 From: OR Member No.: 3,573 Region Association: None |
QUOTE(Mikey914 @ Apr 23 2018, 08:14 AM)  The problem I had was they were a little "soft" You could heat treat them. Just get them red hot and quench them in oil or water to harden. |
|
|
|
| bbrock |
Apr 23 2018, 02:34 PM
Post
#4
|
|
914 Guru Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains
|
QUOTE(Rand @ Apr 23 2018, 01:36 PM) QUOTE(Mikey914 @ Apr 23 2018, 08:14 AM) The problem I had was they were a little "soft" You could heat treat them. Just get them red hot and quench them in oil or water to harden. I tried that with mine and it still wanted to bend. I might have done it wrong, but got it red hot and then dunked in water. Then I beefed it up with some welding. Ugly and still a little soft, but managed to get the job done. I'm in for one made of "the right stuff." |
|
|
|
Posts in this topic
jim_hoyland Member Vendor Apr 22 2018, 08:32 AM
rhodyguy Engman? Apr 22 2018, 08:50 AM walterolin i think it was dlee6204. He was active today. Apr 22 2018, 09:14 AM
jim_hoyland
i think it was dlee6204. He was active today.
... Apr 22 2018, 10:20 AM Dr Evil
i think it was dlee6204. He was active today.
... Apr 23 2018, 09:03 AM McMark I can run these cheap, if he can't or doesn... Apr 23 2018, 09:46 AM McMark The problem I had was they were a little "sof... Apr 23 2018, 02:35 PM Rand
[quote name='Rand' post='2602143' date='Apr 23 20... Apr 23 2018, 03:23 PM McMark With 1" round tube for comfort. Thoughts? Apr 23 2018, 10:15 AM BeatNavy I'd buy it. This is on my to-do list (still ... Apr 23 2018, 10:25 AM LowBridge
I'd buy it. This is on my to-do list (still ... Apr 23 2018, 11:39 AM McMark
Emailed my laser shop to see if they have any rec... Apr 23 2018, 10:31 AM mepstein Id buy a good quality one. I hate cheap tools. Apr 23 2018, 11:07 AM Garold Shaffer
Id buy a good quality one. I hate cheap tools.
... Apr 24 2018, 08:22 AM McMark Laser shop says they can do 3/8" AR500 Steel.... Apr 23 2018, 11:55 AM mmichalik I'd buy one as well. This is coming up on my ... Apr 23 2018, 12:20 PM 914forme I like, and I would love to have all three tools m... Apr 23 2018, 12:20 PM ohbludvlsfan I would buy all three. Apr 23 2018, 01:08 PM John Jentz Wasn't Racer Chris making these???? Apr 24 2018, 08:06 AM Garold Shaffer
Wasn't Racer Chris making these????
I check... Apr 24 2018, 08:27 AM Mikey914 It wasn't Cris,
I can't remember who it wa... Apr 24 2018, 09:11 AM 914forme I don't have a single 914 the uses the stock s... Apr 24 2018, 08:28 PM bulitt Cut one of those trunk spring once to remove it. ... Apr 25 2018, 06:03 AM johnhora
Id buy a good quality one. I hate cheap tools.
... Apr 25 2018, 09:25 AM McMark Should have parts in hand next week. :thumbsup: Apr 25 2018, 09:31 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2024 - 12:39 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.