 Best rear wheel/stub axle bearing, Bearing renew. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 914Toy |
 Jan 8 2019, 12:39 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 718 Joined: 12-November 17 From: Laguna beach Member No.: 21,596 Region Association: Southern California 
 |
What is recommended choice here for trailing arm rear wheel/stub axle bearing - there are two available at Pelican Parts: FAG @ $37.50 with four star rating and SKF @ $75.00 with three star rating?
|
   |
 
|
  |
Replies
| Mark Henry |
Jan 16 2019, 03:34 PM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
How cold is your freezer? I have one that runs about -30 (IMG:style_emoticons/default/smile.gif)
As long as it's been in say 12 hours and the hole is well cleaned out I don't have much issue. Maye some light tapping with a drift or I jury rig a length of threaded rod to pull it in. but yeh... you're always going to run into that boitch, guess I've been lucky, I should be, because I've ran into my fair share of fuchery with other poop. (IMG:style_emoticons/default/rolleyes.gif) |
|
|
|
| BeatNavy |
Jan 16 2019, 04:05 PM
Post
#3
|
|
Certified Professional Scapegoat Group: Members Posts: 2,924 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region
|
QUOTE(Mark Henry @ Jan 16 2019, 04:34 PM)  Apparently not Ontario cold! (IMG:style_emoticons/default/biggrin.gif) |
|
|
|
Posts in this topic
914Toy Best rear wheel/stub axle bearing Jan 8 2019, 12:39 PM
mepstein We usually buy the FAG bearings and have good luck... Jan 8 2019, 12:55 PM Dave_Darling Based on a recent post, you should open up whateve... Jan 8 2019, 12:59 PM
bbrock
Based on a recent post, you should open up whatev... Jan 8 2019, 03:36 PM Mark Henry FAG... not that there's anything wrong with th... Jan 8 2019, 01:12 PM Tom_T Both FAG & SKF used to be considered good prod... Jan 8 2019, 01:30 PM bbrock
Both FAG & SKF used to be considered good pro... Jan 8 2019, 03:39 PM 914Toy Thanks for all of your advice - FAG it is. Jan 8 2019, 03:29 PM dr914@autoatlanta.com fag or skf
What is recommended choice here for ... Jan 8 2019, 03:31 PM 914Sixer Years back I did a comparison on the rear bearings... Jan 8 2019, 05:35 PM bdstone914
Years back I did a comparison on the rear bearing... Jan 17 2019, 08:43 AM Mark Henry To the manufacturer all that matters is the overal... Jan 8 2019, 07:19 PM 914Toy What is DIY method for inserting bearing into trai... Jan 16 2019, 01:21 PM Mark Henry
What is DIY method for inserting bearing into tra... Jan 16 2019, 01:30 PM BeatNavy
What is DIY method for inserting bearing into tr... Jan 16 2019, 01:38 PM mepstein
[quote name='Mark Henry' post='2681624' date='Jan... Jan 16 2019, 03:07 PM 914Toy Thanks for advice - will report back. Jan 16 2019, 02:19 PM Mark Henry
How cold is your freezer? I have one that runs a... Jan 16 2019, 08:28 PM bbrock
Coldest day I've seen here was -35...the day ... Jan 17 2019, 08:23 AM Tbrown4x4 I use a threaded rod with sockets/washers/etc. to ... Jan 16 2019, 09:15 PM falcor75 Be aware that pirate branded bearings is a big iss... Jan 17 2019, 12:40 AM 90quattrocoupe I have been using a hub tool I bought many moons a... Jan 17 2019, 03:55 PM 90quattrocoupe Double post. Jan 17 2019, 04:37 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 05:55 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.