 Engine lid gas strut |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| turnaround89 |
 Dec 13 2019, 08:35 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 671 Joined: 17-May 08 From: Rockford, Illinois Member No.: 9,067 Region Association: Upper MidWest  |
I know this has been done before, but wanted to show off what i did today.
I bought these off amazon Apexstone 45N/10lb 10 inch Gas strut Did a rough install with sheet metal screws (IMG:http://www.914world.com/bbs2/uploads_offsite/i.imgur.com-9067-1576290931.1.jpg) (IMG:http://www.914world.com/bbs2/uploads_offsite/i.imgur.com-9067-1576290931.2.jpg) Once the placement was correct, i welded the brackets to the engine lid and firewall (IMG:http://www.914world.com/bbs2/uploads_offsite/i.imgur.com-9067-1576290932.3.jpg) (IMG:http://www.914world.com/bbs2/uploads_offsite/i.imgur.com-9067-1576290932.4.jpg) The 10 lbs strut is just enough to slow down the engine lid and its still very easy to close the engine lid. Short video of it in action Video |
   |
 
|
  |
Replies
| Mark Henry |
Dec 15 2019, 06:35 AM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
It's only the gt lid that needs this, they slam into the targa bar if you forget to put your hand on it when opening.
My lid has the crossbar cut out and likely won't sit flat with the stock springs. I like how it works now. |
|
|
|
| lierofox |
Dec 16 2019, 01:45 PM
Post
#3
|
|
Member Group: Members Posts: 256 Joined: 23-June 15 From: Paso Robles, CA Member No.: 18,880 Region Association: Southern California 
|
QUOTE(Mark Henry @ Dec 15 2019, 04:35 AM)  It's only the gt lid that needs this, they slam into the targa bar if you forget to put your hand on it when opening. My lid has the crossbar cut out and likely won't sit flat with the stock springs. I like how it works now. Hell I have the standard engine lid on mine, rain tray and all, even has a center stop light mounted on it, and it'll still smack the targa bar if I don't catch it. |
|
|
|
Posts in this topic
turnaround89 Engine lid gas strut Dec 13 2019, 08:35 PM
sixnotfour resize 650x,,, Dec 14 2019, 12:41 AM tvdinnerbythepool @turnaround89 this is cool!
Does this stop t... Dec 14 2019, 06:01 AM ndfrigi Looks like you still have the original spring that... Dec 14 2019, 09:43 AM Mark Henry That's different way of mounting it. :thumbsup... Dec 14 2019, 09:47 AM turnaround89 I left the torsion springs on as it helps lift the... Dec 14 2019, 11:47 AM
ndfrigi
I left the torsion springs on as it helps lift th... Dec 14 2019, 11:53 AM turnaround89 Ahh, understood. Thanks for clarifying. I welded... Dec 14 2019, 11:01 PM porschetub Why fit a strut to a simple system like this that ... Dec 14 2019, 11:58 PM brcacti I use one hand on the pull knob and one on the lid... Dec 15 2019, 08:42 AM ClayPerrine My personal opinion.. this is a solution in search... Dec 15 2019, 07:52 PM FlacaProductions Pulling the release with your left land while you ... Dec 16 2019, 01:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th May 2024 - 02:22 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.