GB clutch cable stop PN 914 423 283 00 DONE now listing shortly, Got some folks looking for these GB $3.50 in Stainless |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
GB clutch cable stop PN 914 423 283 00 DONE now listing shortly, Got some folks looking for these GB $3.50 in Stainless |
Mikey914 |
Feb 19 2020, 11:37 PM
Post
#21
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Played around with a few different alloys. Definitely some are better than others, found the one we will be using and can make it soft enough to work like the OEM part. Bringing in enough to do a production run worthwhile.
George I can set you up too if you want. |
913B |
Feb 20 2020, 01:40 AM
Post
#22
|
Senior Member Group: Members Posts: 846 Joined: 25-April 05 From: South Bay/SoCal Member No.: 3,983 Region Association: None |
Me too
|
dr914@autoatlanta.com |
Feb 20 2020, 10:01 AM
Post
#23
|
914 Guru Group: Members Posts: 7,821 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
good man, Mark. Yes I will buy some
Played around with a few different alloys. Definitely some are better than others, found the one we will be using and can make it soft enough to work like the OEM part. Bringing in enough to do a production run worthwhile. George I can set you up too if you want. |
Literati914 |
Feb 20 2020, 10:23 AM
Post
#24
|
Senior Member Group: Members Posts: 1,440 Joined: 16-November 06 From: Dallas, TX Member No.: 7,222 Region Association: Southwest Region |
I'll take two, thx.
|
914e |
Feb 23 2020, 11:07 PM
Post
#25
|
Member Group: Members Posts: 496 Joined: 21-February 20 From: Arizona Member No.: 23,951 Region Association: Southwest Region |
I'll take two as well.
|
rfinegan |
Feb 24 2020, 05:47 AM
Post
#26
|
Senior Member Group: Members Posts: 973 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region |
I will take 2 please
|
BPic |
Feb 24 2020, 06:03 AM
Post
#27
|
Member Group: Members Posts: 341 Joined: 5-February 18 From: Miami, Florida Member No.: 21,864 Region Association: South East States |
I'm in for 2 please
|
Rob914 |
Feb 24 2020, 07:47 PM
Post
#28
|
Member Group: Members Posts: 113 Joined: 8-April 03 From: Lake Villa, IL Member No.: 541 Region Association: None |
I'm in for two, please.
|
bbrock |
Feb 24 2020, 07:50 PM
Post
#29
|
914 Guru Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains |
I'm in.
|
yellowporky |
Feb 24 2020, 09:39 PM
Post
#30
|
Member Group: Members Posts: 422 Joined: 18-October 09 From: Martinez, Ca. Member No.: 10,948 Region Association: Northern California |
1 for me please
|
Mikey914 |
Feb 25 2020, 12:20 AM
Post
#31
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
I'll be finishing these up tomorrow will be able to start shipping Wednesday!
|
Mikey914 |
Feb 25 2020, 09:32 PM
Post
#32
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Done,
Just need to get these listed up on the site. Trying to figure out how to do the single part alone. Reg mail in a padded envelope run $1 to $1.40 Looking at the reg mail without tracking for those that are willing to risk trusting the post office to deliver. Perhaps with the warning that if it gets lost we have no tracking for you this is at your own risk. Honestly, USPS does a pretty good job most of the time, but there's always the potential to loose something. We are getting these listed up and will PM all shortly. I test fit and bent over the tab today. Fits as it should. -Mark Attached thumbnail(s) |
brant |
Feb 25 2020, 10:03 PM
Post
#33
|
914 Wizard Group: Members Posts: 11,616 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains |
I’m fine without tracking and probably should get more than one
Will you share a link on this thread please When you ready. No rush |
Mikey914 |
Feb 26 2020, 01:17 AM
Post
#34
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Funny,
I can make the parts faster than I can get them listed. Blake will be doing these on Thursday. I can send the PMs out shortly after. Thanks, Mark |
914e |
Feb 28 2020, 02:03 AM
Post
#35
|
Member Group: Members Posts: 496 Joined: 21-February 20 From: Arizona Member No.: 23,951 Region Association: Southwest Region |
Are they up yet? I have few parts in a cart I was hoping to pick these up as well. Then again I seem to be ordering parts every week anyway.
Thanks |
Mikey914 |
Feb 28 2020, 03:23 AM
Post
#36
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Having more of an issue with trying to list the part than making it. Trying to figure out how to add the reg postal shipping that will keep this part inexpensive to ship.
MArk |
Chris914n6 |
Feb 29 2020, 01:10 PM
Post
#37
|
Jackstands are my life. Group: Members Posts: 3,305 Joined: 14-March 03 From: Las Vegas, NV Member No.: 431 Region Association: Southwest Region |
+1
Just put it in the box with everything else.... |
Rleog |
Feb 29 2020, 04:08 PM
Post
#38
|
Senior Member Group: Members Posts: 608 Joined: 12-October 03 From: Middleton, MA Member No.: 1,239 Region Association: North East States |
I’ll take one. Thanks.
|
Mikey914 |
Feb 29 2020, 06:09 PM
Post
#39
|
The rubber man Group: Members Posts: 12,641 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
PMs sent to all this far will keep the GB open for a few weeks so if any stragglers are out there they can get a deal too.
|
euro911 |
Mar 1 2020, 02:32 AM
Post
#40
|
Retired & living the dream. God help me if I wake up! Group: Members Posts: 8,846 Joined: 2-December 06 From: So.Cal. & No.AZ (USA) Member No.: 7,300 Region Association: Southern California |
I should probably get 2 of them (IMG:style_emoticons/default/idea.gif)
Mark - Can you have your guy(s) ship 2 of them along with my tan upholstery order, or the EARLY M/Y TPS board ? ... I'll include the additional $ in the check I'm sending for the other parts you sent - honest (IMG:style_emoticons/default/cool_shades.gif) (IMG:style_emoticons/default/popcorn[1].gif) |
Lo-Fi Version | Time is now: 30th April 2024 - 06:15 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |