 Just another home build 2056 upgrade...but this one is mine!, Redux THrē: It's been so FUN lets do it again..... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rfinegan |
 Jan 19 2021, 08:10 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,162 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region 
 |
Porsche 914 2056 upgrade
1.7 case upgrade from 1.7.> 2.0 now> 2056 53.9 cc (turns out these are 1.8 heads)new 2.0 style chamber with 44 x38 valves and 57 CC cambers 9.0 CR Cam Shaft /lifters RABY 9530. See Cam Card KB 96 Pistons and rings (2.0 rods) EMW H-Beam rods ARP bolts. EMW 2.0 Crank.25/ Standard /.25 rods Webber 40 and 44 carbs Short Pierce style manifolds 3/4 bolt Malory Unilite Grey-Grey Distributor Pete Weber 1 5/8 4-2-1 with Evo 2 muffler Tangerine 1 5/8 stub pipes and with 02 bung at collector Innovate LM-1 with RPM Balance internals Balance Crank NEW lightened/flywheel and Pressure plate with blower 1.7 tins complete 9.0 CR with Deck height to .040 Recommend RPM range. 6200? Est HP GOAL. 130-140 HP? After a tear down of my 2.0l engine I started the build up to the 2056 big bore upgrade. Having a Bridgeport I started with the (5) 3/8 oil galley plug on the block halves Drilling a hole in the plugs and a slide hammer to remove the old plugs then started the installation of the new pugs I was able to order from Type 4 store. https://www.youtube.com/watch?v=50CYceSrBq0 https://www.youtube.com/watch?v=GOMa6nqbkBQ |
   |
 
|
Posts in this topic
rfinegan Just another home build 2056 upgrade...but this one is mine! Jan 19 2021, 08:10 AM
rfinegan Here is a thought I seem to have been over looking... Sep 27 2021, 02:31 PM rfinegan How to notch piston for valve clearance for KB pis... Oct 4 2021, 04:11 PM rfinegan I just opened the box from CFR (tangerine racing) ... Nov 1 2021, 10:05 AM rfinegan another pic as they are just so pretty...and I am ... Nov 1 2021, 03:19 PM rfinegan Heads are in transit back to me from EMW. I will s... Nov 23 2021, 09:45 AM rfinegan Heads and Stubs. Too pretty not to share Nov 29 2021, 05:19 AM rfinegan another pic Nov 29 2021, 07:08 AM Root_Werks Looking good! Getting closer to engine assemb... Nov 29 2021, 10:45 AM GBX0073 Love it
built back even better !!!
Re... Nov 29 2021, 02:01 PM bkrantz More good stuff!
BTW, is it just me, or do ot... Nov 29 2021, 08:16 PM
rfinegan ??? What's getting downloaded? Automaticaly? O... Nov 30 2021, 06:44 AM
BeatNavy
More good stuff!
BTW, is it just me, or do o... Nov 30 2021, 07:10 AM Cairo94507 Yeah, whatever you are downloading is not related ... Nov 30 2021, 07:43 AM GBX0073 bkrantz sent you a pm on what might be the issue
... Nov 30 2021, 10:58 AM rfinegan Today I am going to safety wire the stub nuts for ... Dec 30 2021, 12:48 PM rfinegan Getting ready to put the 2 case half back together... Dec 30 2021, 01:06 PM rfinegan I was inspired to do a recording after seeing a li... Jan 3 2022, 01:50 PM rfinegan Today the loctite 518 sealant arrived so I was abl... Jan 7 2022, 12:07 PM rfinegan tomorrow will be pistons rings and cylinders ....f... Jan 7 2022, 12:10 PM rfinegan Tips of the Day:
When installing the last lock ri... Jan 10 2022, 06:20 AM rfinegan A big thank you to @rick1952 for the head bolt w... Jan 15 2022, 11:54 AM rfinegan other side:
Jan 15 2022, 11:55 AM 930cabman Looking good. I used a strip of duct tape to cover... Jan 15 2022, 04:00 PM rfinegan @[url=http://www.914world.com/bbs2/index.php?showu... Jan 16 2022, 09:31 AM Mark Henry
Looking good. I used a strip of duct tape to cove... Jan 16 2022, 09:39 AM rfinegan @mark henry This is a great tip!
[quote name... Jan 16 2022, 10:34 AM Mark Henry
[b]@[url=http://www.914world.com/bbs2/index.php?s... Jan 16 2022, 10:43 AM rfinegan COLD OUT SIDE!
Cut and replace the 2 bent push... Jan 31 2022, 05:53 PM Root_Werks Getting closer!
Tried to read back through th... Feb 1 2022, 10:59 AM rfinegan I have been happy with the early Italian Weber 44 ... Feb 1 2022, 12:45 PM rfinegan I am not sure if this is the problems the caused m... Feb 2 2022, 07:02 AM rfinegan with additional clearance
Feb 2 2022, 07:03 AM rfinegan and here is #3 intake (one that bent valve) the pi... Feb 2 2022, 07:04 AM rfinegan After a quick clean up , they will be ready to go ... Feb 2 2022, 07:09 AM 930cabman What is your piston to valve clearance? Feb 2 2022, 10:44 AM rfinegan With the new 0.050" valve notches in the pist... Feb 2 2022, 10:55 AM 930cabman
With the new 0.050" valve notches in the pis... Feb 3 2022, 06:43 PM rfinegan Today added the push rod tubes and the rocker arms... Feb 5 2022, 02:25 PM rfinegan another view Feb 5 2022, 02:28 PM ChrisFoley That thermostat is going to heat up pretty quick. ... Feb 6 2022, 08:29 AM 76-914 Maybe a small metal heat shield between the therm ... Feb 6 2022, 08:47 AM rfinegan Today I finished the rockers and pushrods and set ... Feb 14 2022, 02:25 PM rfinegan I think I'll add a piece of coat hanger as a p... Feb 14 2022, 02:29 PM rfinegan Engine installed and cranked over without plugs un... Feb 21 2022, 04:08 PM 930cabman
Engine installed and cranked over without plugs u... Feb 21 2022, 04:22 PM rfinegan First pic is there it hits.
Here is the full shot... Feb 21 2022, 04:09 PM rfinegan ...after about the 3rd crank at about 15 sec each.... Feb 21 2022, 04:34 PM ChrisFoley Better to alter the rod than the stubs.
You can fl... Feb 22 2022, 03:23 PM rfinegan Thanks @[url=http://www.914world.com/bbs2/index.p... Feb 23 2022, 06:05 AM rfinegan This is getting interesting...I think some on set ... Mar 5 2022, 10:23 AM rfinegan Working on the shifter clearance it from hitting t... Mar 6 2022, 04:59 PM Cairo94507 Nice progress Robert. You will be driving that ba... Mar 7 2022, 07:35 AM rfinegan @Cairo94507 The Engine is running now ...working ... Mar 7 2022, 09:35 AM rfinegan I need some help PLEASE.
I have the engine back i... Mar 12 2022, 12:22 PM rfinegan It's been so much fun, lets do it again?
Since... Mar 13 2022, 02:45 PM ddire333 Well that sucks, sorry don't have any suggesti... Mar 13 2022, 04:03 PM BeatNavy I agree that sucks Robert. Are you sure it's ... Mar 13 2022, 04:23 PM rfinegan
I agree that sucks Robert. Are you sure it's... Mar 13 2022, 04:39 PM 930cabman
I agree that sucks Robert. Are you sure it... Mar 17 2022, 09:30 AM rfinegan I'm going to do another compression test and m... Mar 13 2022, 04:33 PM VaccaRabite Is the howling noise the noise you re concerned ab... Mar 17 2022, 11:07 AM rfinegan To me it sounds like a dry bearing and pulls /slow... Mar 17 2022, 11:47 AM Root_Werks Could it have been a tight thrust play? Maybe som... Mar 17 2022, 07:46 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th January 2026 - 04:27 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.