Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 Forum Rules Classified Rules!
 
 Reply to this topicStart new topic
> 914-6 W/ COA
roblav1
post Sep 24 2021, 08:38 AM
Post #1


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
This is Stephan's car. Just had it soda / media blasted yesterday. It's more of a project than what I'm willing to take on in the short term. Don't have a lot of time right now to create a better advert here because it's all bare steel, and it needs prep and painted. I'm about to spray DPLF epoxy white on the painted components and black on the typical black parts. I'm letting it go now because there's not many left and it should be done right.

This car is complete and has boxes and boxes of original and additional parts. My trailer is full. Car is sitting in a rotisserie.

Structurally extremely solid. Rockers, both hell holes, firewall, suspension consoles are excellent. There's a few rust spots on the pan, the pedal support steel (bought one new) and some on the body. The rear trunk floor should have the rear portion replaced. Rotisserie rear is attached to the transmission mounts to perform this.

Extra dashboards (one with no crack), rear bumper and valence here, a couple of original air cleaners, extra hoods, trunk lids, engine lids, aluminum trim, 2 windshields. Etc... Everything is here to build up a really nice car.

I have my 1973 3.0 GT build to finish first, so I really need to let this go.

I need $43K. No haggle. In Somerset, KY. First person with funds and a trailer to pick it up gets it.

There's also 5 15x6 Flat Fuchs available for an additional $2K.

Hope you're all enjoying Okteenerfest!

Rob


Attached thumbnail(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Sea Rooster
post Sep 25 2021, 10:08 AM
Post #2


Member
**

Group: Members
Posts: 106
Joined: 8-March 18
From: Nashville, TN
Member No.: 21,948
Region Association: South East States
Engine and tranny included? Condition of both?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Sep 25 2021, 04:45 PM
Post #3


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
Mileage is 59251. Title / Bill of sale is notarized at that mileage. Yes, original engine and transaxle. Previous owner's father rebuilt the engine but never timed the cams or installed it. Transmission is very clean looking, but I've not taken it apart to inspect. I just put Ospho on the chassis yesterday and prepping for fab/ welding.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Sep 25 2021, 04:50 PM
Post #4


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
Here's the car just before it went in the rotisserie.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
eyeguy
post Sep 26 2021, 07:51 PM
Post #5


Newbie
*

Group: Members
Posts: 1
Joined: 26-February 19
From: johnson city, tn
Member No.: 22,911
Region Association: MidAtlantic Region
interested , and not to far from you in tennessee. Is there a number where I can contact you?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Sep 26 2021, 08:31 PM
Post #6


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
Thanks Eyeguy. I'll PM you with my number.

Here's a few pictures of the bottom of the chassis and firewall. Given what I've often seen (and worked) in 914's and early 911/912's, I don't think this is too bad at all.

I took those pictures at 5:00 PM today (you can see my clock!). Black specs on front pan are rubber specs that didn't come off. Firewall is perfect, both upper and lower. Main pan has a lovely riveted patch on passenger side, the pedal support area needs some fab and welding, and both front donut areas need some attention... and a few pinholes here and there that look like relatively simple filling with steel wire and a TiG. Some other areas topside need some attention, and the rear trunk floor needs some fairly major help. This is a very structurally sound car.

I have a few other pictures if anyone needs them.

To be clear, I've wanted one of these since I was young, and I'm certainly capable of finishing it. But I just sold the house, and there's enough other stuff to move...

Unless someone wants my almost finished Bahia Red GT w/ Euro Carrera 3.0 done right! I just don't want to be working on and moving two cars with everything else going on.


Attached image(s)
Attached Image Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Sep 30 2021, 10:48 AM
Post #7


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
Due to the overwhelming response and the federal contractor vax Executive Order, I will keep this car and finish. I need something fun to do while unemployed!

I've thought about doing fabwork and welding old Porsches as sidework. We'll see where this goes.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Oct 18 2021, 04:11 PM
Post #8


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
It seems I'm not yet destined to retire and stay home working on old Porsches. So this -6 is back on the market again. Apologies for any inconveniences or holdups.

If packaged well, everything might fit in a 24 foot enclosed trailer. A lot of 914 extras come with the car... windshields, body panels, trim, lights, small stuff. Calipers and brake proportion valve done by PMB. I spent a couple days tigging new steel on the lower passenger side. I estimate 3-4 more full days of metalwork on the tub. In my experience with old non-zinc coated Porsches, this tub is pretty good.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Oct 29 2021, 08:26 PM
Post #9


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
I have a verbal agreement on this car.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
roblav1
post Nov 13 2021, 01:16 PM
Post #10


Senior Member
***

Group: Members
Posts: 528
Joined: 18-September 12
From: KY
Member No.: 14,943
Region Association: MidAtlantic Region
This car is sold. Thanks for all the inquiries.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · FS/WANTED: 914 Cars and Rollers · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 19th May 2024 - 05:41 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...