 What's wrong with this picture? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Mikey914 |
 Nov 2 2021, 11:51 AM
Post
#1
|
|
The rubber man  Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None 
 |
This one is a little special to me. It's the last part Cary asked me to make.
Attached thumbnail(s) 
|
   |
 
|
| mepstein |
Nov 2 2021, 11:56 AM
Post
#2
|
|
914-6 GT in waiting Group: Members Posts: 19,274 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region
|
Is your rubber piece too short?
|
|
|
|
| Mikey914 |
Nov 2 2021, 12:01 PM
Post
#3
|
|
The rubber man Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
Actually, this is a piece we didn't make but is being sold as a clutch stop. We had purchased them to resell. But they aren't right for the clutch stop.
|
|
|
|
| SirAndy |
Nov 2 2021, 12:04 PM
Post
#4
|
|
Resident German Group: Admin Posts: 41,644 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
Use two and sell it as: "too long, needs trimming"
(IMG:style_emoticons/default/idea.gif) |
|
|
|
| Mikey914 |
Nov 2 2021, 12:14 PM
Post
#5
|
|
The rubber man Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
Much better
Attached thumbnail(s) 
|
|
|
|
| Mikey914 |
Nov 2 2021, 12:21 PM
Post
#6
|
|
The rubber man Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
We plan to do a GB for these at $3 for both pierces. Just thought Id post this up as I promised Cary Id make these. So its not just the part, but my way of getting some closure. It bothered me seeing the sample sitting on my desk (IMG:style_emoticons/default/beer3.gif) |
|
|
|
| 914Sixer |
Nov 2 2021, 01:20 PM
Post
#7
|
|
914 Guru Group: Members Posts: 8,882 Joined: 17-January 05 From: San Angelo Texas Member No.: 3,457 Region Association: Southwest Region
|
The part is for the pedal assembly brake stop.
|
|
|
|
| bdstone914 |
Nov 2 2021, 03:21 PM
Post
#8
|
|
bdstone914 Group: Members Posts: 4,522 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
It is the brake and clutch pedal stop for the pedal set. It is a different profile abd does not fit the pedal board stop unkess you grind down the back side.
|
|
|
|
| Mikey914 |
Nov 2 2021, 04:38 PM
Post
#9
|
|
The rubber man Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
We’ve made an extrusion that an do both
|
|
|
|
| bdstone914 |
Nov 2 2021, 05:00 PM
Post
#10
|
|
bdstone914 Group: Members Posts: 4,522 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
QUOTE(Mikey914 @ Nov 2 2021, 03:38 PM)  We’ve made an extrusion that an do both @Mikey914 What will be the price for the brake pedal stop? The aftermarket ones are $2.50 from Pelican. I use a lot of them. |
|
|
|
| Mikey914 |
Nov 3 2021, 02:00 PM
Post
#11
|
|
The rubber man Group: Members Posts: 12,669 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None
|
The GB will be $3 for both. As far as hooking you up with a bulk price I can save you money on that. Mark
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th May 2024 - 12:11 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.