 Engine drop easy to do list |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| emerygt350 |
 Jun 21 2023, 02:29 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,132 Joined: 20-July 21 From: Upstate, NY Member No.: 25,740 Region Association: North East States  |
Dropping the engine soon (next week). Although replacing the oil cooler seals was easy without dropping the engine, the cooler itself was toast.
So, new cooler and seals are on their way from autoAtlanta, as well as new seals for the pushrod tubes. Anything else I should touch up while it is down? It is going to be sitting on the tangerine racing engine removal plate. The seals on the side of the transmission need to be replaced. Is that something I can do without pulling the transmission apart? I have ordered the cv gaskets as well. |
   |
 
|
Posts in this topic
emerygt350 Engine drop easy to do list Jun 21 2023, 02:29 PM
Shivers It is worth the work to freshen up the main seals. Jun 21 2023, 02:38 PM emerygt350 I assume you don't need to crack the case for ... Jun 21 2023, 02:39 PM
Shivers
I assume you don't need to crack the case for... Jun 21 2023, 03:26 PM 930cabman Hmmm, while the engine is out ....................... Jun 21 2023, 03:27 PM rhodyguy New engine bay seals. The task will never be easie... Jun 21 2023, 03:35 PM 930cabman
New engine bay seals. The task will never be easi... Jun 22 2023, 01:47 PM r_towle this is a big can of worms unless you don't ge... Jun 21 2023, 04:08 PM rfinegan I did both CV shaft hub seals when I took my engin... Jun 21 2023, 04:56 PM emerygt350 Great. What are the seals called? I was browsing... Jun 21 2023, 05:30 PM Superhawk996 96mm pistons easy when engine is out :rotfl: Jun 21 2023, 05:35 PM emerygt350
96mm pistons easy when engine is out :rotfl:
... Jun 21 2023, 06:13 PM r_towle
96mm pistons easy when engine is out :rotfl:
... Jun 21 2023, 06:21 PM r_towle Output Shaft Seal
https://pmbperformance.com/prod... Jun 21 2023, 05:36 PM emerygt350
Output Shaft Seal
https://pmbperformance.com/pro... Jun 21 2023, 06:13 PM rjames I've never dropped the engine in my car, but I... Jun 21 2023, 06:49 PM emerygt350 Yeah, heads too. I think I will try to build a wo... Jun 21 2023, 07:28 PM brubou I use an engine stand with a cradle bolted to the ... Jun 21 2023, 07:34 PM r_towle When I pull an engine, I remove the exhaust first,... Jun 21 2023, 07:44 PM r_towle Two guys can lift a type 4 onto a stand.
I used to... Jun 21 2023, 07:46 PM emerygt350 What is the minimum height I should raise the car ... Jun 22 2023, 10:23 AM bkrantz
What is the minimum height I should raise the car... Jun 22 2023, 09:12 PM Dave_Darling I always get the rear of the car as high in the ai... Jun 22 2023, 05:14 PM VaccaRabite
Note that you will need the biggest flat-head scr... Jun 22 2023, 08:16 PM Dave_Darling
Gunsmith screwdrivers or the flathead screw bits ... Jun 25 2023, 04:40 AM r_towle As high as you can get it.
If you find you cannot ... Jun 22 2023, 08:27 PM emerygt350 About that rear valence...
I will just try to g... Jun 23 2023, 04:58 AM rhodyguy With carbs clearance can be tight. I remove mine a... Jun 23 2023, 07:00 AM r_towle The way I do it is with a dolly.
1) top of engine ... Jun 23 2023, 07:22 AM r_towle Tools,
2 floor jacks
12 point tool to remove cv jo... Jun 23 2023, 07:32 AM r_towle I assume your front spoiler is removable….go do ... Jun 23 2023, 07:33 AM emerygt350 No chance I can remove the dam.
I have the tang... Jun 23 2023, 11:37 AM r_towle Remove muffler, you can leave the exchangers on.
I... Jun 23 2023, 11:39 AM emerygt350 Yeah, would rather leave the studs alone.
I have ... Jun 23 2023, 01:03 PM SirAndy http://www.914world.com/specs/tech_engdrop1.php
... Jun 23 2023, 01:22 PM emerygt350 Thank you sir Andy, couple of things in those link... Jun 23 2023, 08:58 PM emerygt350 What do you guys think about me putting the origin... Jun 23 2023, 09:01 PM Shivers
What do you guys think about me putting the origi... Jun 24 2023, 08:09 AM emerygt350
What do you guys think about me putting the orig... Jun 24 2023, 12:16 PM r_towle Is it out yet? Jun 23 2023, 09:25 PM emerygt350 Haven't even crawled out of bed yet! Jun 24 2023, 07:14 AM emerygt350 Everything is ready for the drop but I have a stri... Jun 24 2023, 11:34 AM SirAndy
Everything is ready for the drop but I have a str... Jun 24 2023, 11:42 AM emerygt350 Heat and extractor got it out. All ready to drop ... Jun 24 2023, 01:33 PM r_towle if it was done right originally, the outer rubber ... Jun 24 2023, 02:08 PM emerygt350 It was a tough delivery.
Jun 24 2023, 03:07 PM Superhawk996 :lol4:
Now you’re no longer an engine drop vir... Jun 24 2023, 03:18 PM emerygt350 I hope not. Jun 24 2023, 04:37 PM Shivers Just put a zipper in now. :D Jun 24 2023, 08:58 PM bkrantz Any time you feel cocky about dropping a 914 motor... Jun 25 2023, 09:22 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd June 2024 - 10:50 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.