Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> aa performance products, run away ??
jimkelly
post Nov 19 2005, 10:05 PM
Post #1


Delaware USA
****

Group: Members
Posts: 4,969
Joined: 5-August 04
From: Delaware, USA
Member No.: 2,460
Region Association: MidAtlantic Region



on ebay p&c's

http://www.aaproductsinc.com/cgi-bin/Porsc..._busesprice.cgi
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
GWN7
post Nov 19 2005, 10:49 PM
Post #2


King of Road Trips
*****

Group: Members
Posts: 6,280
Joined: 31-December 02
From: Winnipeg, MB, Canada
Member No.: 56
Region Association: Northstar Region



I've never heard of them......no address, no contact person, no phone numbers. I like to know who and where internet business are located before doing any business with them.

"If" they had all that machinary I'm sure someone would have heard about them.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
TINCAN914
post Nov 19 2005, 11:04 PM
Post #3


Summer's Commin...
****

Group: Members
Posts: 2,440
Joined: 18-August 05
From: Colorado Springs, CO.
Member No.: 4,611
Region Association: Rocky Mountains



address and info.
AA Performance Product, Inc.

450 2nd Avenue, San Francisco, CA 94118

Tel: (415) 752-2075 Fax: (415) 752-2114



Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Nov 19 2005, 11:19 PM
Post #4


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None



I've used them before...this company supplied P/Cs to Mark Stephens and other engine builders.

Pistons made in Japan, cylinders made in Tawain

I believe European Motorsports or Motorworks uses them as well as many other shops.

Jake does not care for them, but they do work...tend to be a tad bit louder at startup until they warm up.



User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Nov 19 2005, 11:20 PM
Post #5


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None



Oh yea...no relationship to Automobile Atlanta
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
sixnotfour
post Nov 19 2005, 11:23 PM
Post #6


914 Wizard
**********

Group: Members
Posts: 10,650
Joined: 12-September 04
From: Life Elevated..planet UT.
Member No.: 2,744
Region Association: Rocky Mountains



Did they use to be American Aircooled back in the 90's?
User is online!Profile CardPM
Go to the top of the page
+Quote Post
anthony
post Nov 19 2005, 11:49 PM
Post #7


2270 club
****

Group: Benefactors
Posts: 3,107
Joined: 1-February 03
From: SF Bay Area, CA
Member No.: 218



QUOTE (Mueller @ Nov 19 2005, 10:19 PM)
Jake does not care for them, but they do work...tend to be a tad bit louder at startup until they warm up.

Jake seems to carry them in his online store. I wonder if he does anything extra to them before they get shipped out?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jimkelly
post Nov 20 2005, 06:17 AM
Post #8


Delaware USA
****

Group: Members
Posts: 4,969
Joined: 5-August 04
From: Delaware, USA
Member No.: 2,460
Region Association: MidAtlantic Region



thanks for the replies.

glad I did not get slammed with - use search - cause I did bt found nothing : )

prices look very good - see lower prices on ebay then on their webpage.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Nov 20 2005, 06:20 AM
Post #9


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None



QUOTE (jimkelly @ Nov 20 2005, 05:17 AM)
thanks for the replies.

glad I did not get slammed with - use search - cause I did bt found nothing : )

prices look very good - see lower prices on ebay then on their webpage.

just make sure you inspect them good, the 1st set I bought from them one cylinder had a crack near the bottom (dropped at one time), another one had a small inclusion near the top from bad casting job...they replaced them with no questions asked...in fact they had one of thier people hand deliver them to me,
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bd1308
post Nov 20 2005, 07:38 AM
Post #10


Sir Post-a-lot
*****

Group: Members
Posts: 8,020
Joined: 24-January 05
From: Louisville,KY
Member No.: 3,501



I wouldn't run....it increases the risk of doing a faceplant in the road.

Just walk slightly faster than you usually would.

b
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jimkelly
post Nov 20 2005, 08:19 AM
Post #11


Delaware USA
****

Group: Members
Posts: 4,969
Joined: 5-August 04
From: Delaware, USA
Member No.: 2,460
Region Association: MidAtlantic Region



I'd say mueller gave them a cauiously decent rating.

still got thet 2.0 long block?

jim
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bottomend
post Nov 20 2005, 01:17 PM
Post #12


Member
**

Group: Members
Posts: 180
Joined: 27-August 05
From: LA,Ca
Member No.: 4,683



There is a guy at the Shop Talk forums who is drag racing with this stuff. Do a search over there and I'm sure you'll find the info. I cant remember his name off the top of me head. (Actaully I can rememeber his name, I just cant read it off the top of me head. Anybody got a ladder and wanna help me see what I wrote up there?)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Jake Raby
post Nov 20 2005, 04:31 PM
Post #13


Engine Surgeon
*****

Group: Members
Posts: 9,398
Joined: 31-August 03
From: Lost
Member No.: 1,095
Region Association: South East States



I offer them as an "ECONO" set for getting engines back on the road. I do not care for their rings at all and replace them as soon as they come into my shop.

I also magna flux all the cylinders, because I have seen them with holes right through the castings that give comopression leaks.

They are only good for patch jobs, IMHO...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SirAndy
post Nov 20 2005, 04:52 PM
Post #14


Resident German
*************************

Group: Admin
Posts: 41,920
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California



i don't know, trust a guy who can't even spell the name of the city he lives in? (IMG:http://www.914world.com/bbs2/html/emoticons/confused24.gif)

=========================================
Shawn Chi
shawn@itgo2u.com
415-867-2921
AA Products international
668 Dartmouth st
Sab francisco,CA,US 94134
=========================================
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
anthony
post Nov 20 2005, 05:13 PM
Post #15


2270 club
****

Group: Benefactors
Posts: 3,107
Joined: 1-February 03
From: SF Bay Area, CA
Member No.: 218



Jake, are the EMW cylinders that you sell a lot higher quality?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Nov 20 2005, 07:25 PM
Post #16


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None



QUOTE (SirAndy @ Nov 20 2005, 03:52 PM)
i don't know, trust a guy who can't even spell the name of the city he lives in? (IMG:http://www.914world.com/bbs2/html/emoticons/confused24.gif)

=========================================
Shawn Chi
shawn@itgo2u.com
415-867-2921
AA Products international
668 Dartmouth st
Sab francisco,CA,US 94134
=========================================

They are "english" challanged, I've talked to them a few times and the main guy gave me the skinny on what Mark Stephens is up to now (or was when he shut down his business)

Like I said, the stuff works, but don't expect the same life or duty that you'd get from factory or the more expensive stuff.......

for a lot of people here, they'll work fine and their motors will never know the differance
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 6th December 2024 - 11:33 AM