914World.com - The largest online 914 community!

51x9,15x10 or 11 Fuch wheels - where to get?, different backspacings available??

byndbad914	Feb 2 2006, 06:14 PM Post #1
shoehorn and some butter - it fits Group: Members Posts: 1,547 Joined: 23-January 06 From: Broomfield, CO Member No.: 5,463 Region Association: None	So I like the look of the Fuch 5-bolts and want to put them on my car, but I need a deep backspace set. I was hoping to find out if anyone knows where to get them with the centers moved... Want 15x9 with a 4-1/2" to 5" backspace and 15x10 with 5-1/2 to 6... maybe 15x11 with 6-1/2 to 7" if I can figure out how to squeeze them under the rearend flares. Apparently to even find Fuch wheels this size is nearly impossible, let alone with custom backspace. Stock I think is way to shallow/"dished". Thanks, Tim (IMG:http://www.914world.com/bbs2/html/emoticons/help.gif)

ewdysar	Feb 2 2006, 06:25 PM Post #2
What happens here, stays here. Group: Members Posts: 558 Joined: 29-October 04 From: Altadena, CA Member No.: 3,030	Check for tire size availability before you commit to wide rims. There's not much wide rubber for 15 and 16 inch rims these days. Eric

racerx7	Feb 2 2006, 06:25 PM Post #3
Member Group: Members Posts: 119 Joined: 28-January 06 From: Belmont, CA 94002 Member No.: 5,489	Does it have to Fuch wheel? These two companys will make what ever size you want. Complete Custom Fiske

byndbad914	Feb 2 2006, 06:42 PM Post #4
shoehorn and some butter - it fits Group: Members Posts: 1,547 Joined: 23-January 06 From: Broomfield, CO Member No.: 5,463 Region Association: None	the tires I run are the DOT Hoosiers 245-50-15 on my 15x8-1/2" and the 245-50-15 and 275-50-15 would fit the 9 and 10. 11s would be pushing it, so probably just stick to 10s to make fitment easier on the car too. and yeah, specifically Fuchs. Fikse doesn't even make anything under 17" if remember right - they have one wheel I really like, but it is 17" minimum for sure. Old skooler here... I like the 15" rubber on the teens v. the rubberbands... :smiley with a cane needed:

d914	Feb 2 2006, 06:50 PM Post #5
Advanced Member Group: Members Posts: 2,350 Joined: 12-July 03 From: Atlanta, ga Member No.: 904 Region Association: South East States	possibly HRE, fuchs center, three piece wheel...don't know dia... other way would be some older three piece bbs's

racerx7

Feb 2 2006, 06:57 PM

Post #6

Member

Group: Members
Posts: 119
Joined: 28-January 06
From: Belmont, CA 94002
Member No.: 5,489

QUOTE (byndbad914 @ Feb 2 2006, 04:42 PM)

the tires I run are the DOT Hoosiers 245-50-15 on my 15x8-1/2" and the 245-50-15 and 275-50-15 would fit the 9 and 10. 11s would be pushing it, so probably just stick to 10s to make fitment easier on the car too.

and yeah, specifically Fuchs. Fikse doesn't even make anything under 17" if remember right - they have one wheel I really like, but it is 17" minimum for sure.

Old skooler here... I like the 15" rubber on the teens v. the rubberbands... :smiley with a cane needed:

That sucks that they do not do 15. They are suppose to be known
for racing cars. I guess now it is all about the bling.

I did like the fiske 17 on my rx7.

sixnotfour	Feb 2 2006, 07:00 PM Post #7
914 Wizard Group: Members Posts: 11,345 Joined: 12-September 04 Member No.: 2,744 Region Association: NineFourteenerVille	I have some 16x9 and 16x 10 fuchs 3 piece wheels , 6inch backspace, I run a 1/4 spacer. 5.50 would be better , depending on your tire section width. From PP Some Sources for Custom Fuchs-Centered Wheels Ernies Alloys 13640 NW 19th Avenue #9 Miami, FL 33054 Builds 2 and 3-piece wheels using real Fuchs centers. (305) 687-0028 Jae Lee, Mirage International San Diego, CA Builds 2 and 3-piece wheels using real Fuchs centers. 858) 581-1101 Lindsey Racing 530 N. Meridian Ave. Oklahoma City, OK 73107 Builds 2 and 3-piece wheels using real Fuchs centers. Tech and Info: (405) 947.0137 Ordering (Toll Free) (877) 943.3565 Gary Stratton, Stratton Motorsport Orlando, Florida Builds any size 3-piece Fuchs with factory centers, BBS hardware and wheel halves. Also widens Fuchs wheels by welding, (407) 629-1911 CarsRUS@aol.com Truedesign wheels (Jim Lyon) 12200 W 52nd Ave #4 Wheat Ridge, CO 80033 Builds 2 and 3-piece wheels using real Fuchs centers. About $350-375 for 3-piece; about $250-$280 for 2-piece wheels (303) 422-5090 (800) 621-6436 jims4848@comcast.net Weidman Wheels Oroville, CA Can widen 6->7" wheel (530) 534-7903.

byndbad914	Feb 2 2006, 07:45 PM Post #8
shoehorn and some butter - it fits Group: Members Posts: 1,547 Joined: 23-January 06 From: Broomfield, CO Member No.: 5,463 Region Association: None	schweet, thanks 6not4! (IMG:http://www.914world.com/bbs2/html/emoticons/beerchug.gif) That will give me a few people to call and irritate with questions and pricing (IMG:http://www.914world.com/bbs2/html/emoticons/wink.gif)

sixnotfour	Feb 2 2006, 07:52 PM Post #9
914 Wizard Group: Members Posts: 11,345 Joined: 12-September 04 Member No.: 2,744 Region Association: NineFourteenerVille	here is some more candy http://www.lindseyracing.com/Merchant2/mer..._Code=GENWHEELS wait untill you see the prices (IMG:http://www.914world.com/bbs2/html/emoticons/laugh.gif) mine are the yellow center p-3's

byndbad914	Feb 2 2006, 08:05 PM Post #10
shoehorn and some butter - it fits Group: Members Posts: 1,547 Joined: 23-January 06 From: Broomfield, CO Member No.: 5,463 Region Association: None	yeah, I was checking out that site after your first post, those prices (IMG:http://www.914world.com/bbs2/html/emoticons/head_hurts_kr.gif) Think I will be calling out to Wheatridge for the sub $300 range (IMG:http://www.914world.com/bbs2/html/emoticons/wink.gif) What car do you have those wheels on? I checked your blog and didn't see anything with yellow wheels...

ArtechnikA	Feb 2 2006, 08:05 PM Post #11
rich herzog Group: Members Posts: 7,390 Joined: 4-April 03 From: Salted Roads, PA Member No.: 513 Region Association: None	the last pair of NOS 15x11 RSR Fuchs I saw change hands went for $10k+. there was a used pair at Hershey last year that sold for about $8k. with more than the standard 4-7/8" backspace you'll need spacers to keep the insides off the suspension bits...

michel richard	Feb 2 2006, 08:11 PM Post #12
Senior Member Group: Members Posts: 1,291 Joined: 22-July 03 From: Longueuil, Québec Member No.: 936	Those two piece and three piece wheels that are manufactued using original Fuchs centers, would they be allowed on a track at a PCA event ?

SirAndy

Feb 2 2006, 08:39 PM

Post #13

Resident German

Group: Admin
Posts: 42,498
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California

QUOTE (byndbad914 @ Feb 2 2006, 04:42 PM)

the tires I run are the DOT Hoosiers 245-50-15 on my 15x8-1/2" and the 245-50-15 and 275-50-15 would fit the 9 and 10. 11s would be pushing it, so probably just stick to 10s to make fitment easier on the car too.

if you're talking stock GT flares, 11" won't fit. even the 10" is pushing it, they won't fit with the 285/40 that the factory ran on the 9" ...

factory setup for the GTs was 245/45 x15 on 8" for the front and 285/40 x 15 on 9" for the rear.

as far as i know, *no* one makes the 285/40 street tires anymore. and trust me, i looked for them ...
there are still some 285/40 pirelli tires floating around from time to time (ebay) but be aware of the fact that pirelli hasn't made those in 15 years. even if advertised as *new*, they will be at least that old ...

(IMG:http://www.914world.com/bbs2/html/emoticons/dry.gif) Andy

byndbad914	Feb 2 2006, 09:17 PM Post #14
shoehorn and some butter - it fits Group: Members Posts: 1,547 Joined: 23-January 06 From: Broomfield, CO Member No.: 5,463 Region Association: None	thanks Andy - I have the Sheridan body kit on the car. Right now my 8-1/2" wheels are somewhat deep dish, so the tire is right at the fender, but I have a couple inches to grow toward the inner fender before I hit it or the trailing arm...

SirAndy

Feb 2 2006, 09:38 PM

Post #15

Resident German

Group: Admin
Posts: 42,498
Joined: 21-January 03
From: Oakland, Kalifornia
Member No.: 179
Region Association: Northern California

QUOTE (byndbad914 @ Feb 2 2006, 07:17 PM)

thanks Andy - I have the Sheridan body kit on the car. Right now my 8-1/2" wheels are somewhat deep dish, so the tire is right at the fender, but I have a couple inches to grow toward the inner fender before I hit it or the trailing arm...

aha, schweet! narrow or widebody? roger's stuff is top notch!

(IMG:http://www.914world.com/bbs2/html/emoticons/smilie_pokal.gif) Andy

roger's own car at laguna last year ... (IMG:http://www.914world.com/bbs2/html/emoticons/wub.gif)

Attached thumbnail(s)

SirAndy	Feb 2 2006, 09:39 PM Post #16
Resident German Group: Admin Posts: 42,498 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California	and scott's car with the same kit at the same event ... (IMG:http://www.914world.com/bbs2/html/emoticons/driving.gif) Attached thumbnail(s)

Mueller

Feb 2 2006, 10:00 PM

Post #17

914 Freak!

Group: Members
Posts: 17,155
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None

QUOTE (michel richard @ Feb 2 2006, 07:11 PM)

Those two piece and three piece wheels that are manufactued using original Fuchs centers, would they be allowed on a track at a PCA event ?

I've never heard of someone failing tech due to the frankenstien Fuchs, but I have heard of them failing a few years ago on the track (IMG:http://www.914world.com/bbs2/html/emoticons/headbang.gif)

....problem was linked to the lack of a sufficient radius being machined into the Fuchs center (a bolted together wheel, not a welded unit )...Dave Darling knows the couple that owns the car, it got damaged pretty good from what I remember.....

just remember, these are 20 to 30 year old rims that who knows what kind of abuse they had been put thru....then add even wider rim halves and sticky tires to really push the limits of the rim center (IMG:http://www.914world.com/bbs2/html/emoticons/wacko.gif)

TimT

Feb 2 2006, 10:14 PM

Post #18

retired

Group: Members
Posts: 4,033
Joined: 18-February 03
From: Wantagh, NY
Member No.: 313

I have a set of 15X9 and 15X11 Simmons wheels that are available. Like mentioned by Rich 15X9 Fuchs are Uber expensive.

QUOTE

Those two piece and three piece wheels that are manufactued using original Fuchs centers, would they be allowed on a track at a PCA event ?

Yes many aftermarket wheels are allowed on the track by PCA and other race groups. Kinesis, Fikse,Borbet, BBS, CCW, Jongbloed, the list goes on. I think the PCA rule was trying to get the cheap fake Fuchs off the track

Aaron Cox	Feb 3 2006, 12:04 AM Post #19
Professional Tinkerer Group: Retired Admin Posts: 24,548 Joined: 1-February 03 From: Corona, CA Member No.: 219 Region Association: Southern California	here are some 15x12's http://cgi.ebay.com/ebaymotors/Porsche-Fuc...609056702QQrdZ1

1973914

Feb 3 2006, 08:39 AM

Post #20

Member

Group: Members
Posts: 353
Joined: 16-May 03
From: Washington, DC
Member No.: 703

QUOTE (TimT @ Feb 2 2006, 08:14 PM)

I have a set of 15X9 and 15X11 Simmons wheels that are available. Like mentioned by Rich 15X9 Fuchs are Uber expensive.

QUOTE

Those two piece and three piece wheels that are manufactued using original Fuchs centers, would they be allowed on a track at a PCA event ?

Yes many aftermarket wheels are allowed on the track by PCA and other race groups. Kinesis, Fikse,Borbet, BBS, CCW, Jongbloed, the list goes on. I think the PCA rule was trying to get the cheap fake Fuchs off the track

what do those look like?

« Next Oldest · 914World Garage · Next Newest »

2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)

0 Members: