tranny conversion |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
tranny conversion |
914 dror |
Jul 27 2006, 06:42 AM
Post
#1
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
I have a `71 914 and I want to convert to the side shifter tranny
How do I go about it? Do some body out there makes a kit ? dror |
SLITS |
Jul 27 2006, 07:02 AM
Post
#2
|
"This Utah shit is HARSH!" Group: Benefactors Posts: 13,602 Joined: 22-February 04 From: SoCal Mountains ... Member No.: 1,696 Region Association: None |
1st .......SEARCH
The components required have been discussed many times. But.....here you go: 1.) Sideshift tranny 2.) Sideshift shifter, front bar, rear bar 3.) Conversion bushing for firewall 4.) Late style engine bar 5.) Late style engine bar mounts 6.) Late style motor mounts 7.) Late style engine mounts Generally, #1, #2, #4, #5, #7 you purchase from a non-members who are parting a cars. #3 and #6 you get from parts houses. |
Brad Roberts |
Jul 27 2006, 12:08 PM
Post
#3
|
914 Freak! Group: Members Posts: 19,148 Joined: 23-December 02 Member No.: 8 Region Association: None |
Are you really in Israel?
Do you need part numbers? or parts? B |
So.Cal.914 |
Jul 27 2006, 12:17 PM
Post
#4
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
How many 914's in your neck of the woods?
Keep your head down and (IMG:style_emoticons/default/welcome.png) |
914 dror |
Jul 30 2006, 11:34 PM
Post
#5
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
1st .......SEARCH Thanks SLITS I’m gonna use that search for getting some more info. The thing is that I have a side shifter on my 71 914 but it looks like its a shitty conversion with few right parts and few improvised. And I need to see some pics. Of a conversion done right! There is also the issue of the rubber garments or boots to protect the joints areas Which I don’t know what would fit. After I’ll know better what I need I’ll try to look for it. dror The components required have been discussed many times. But.....here you go: 1.) Sideshift tranny 2.) Sideshift shifter, front bar, rear bar 3.) Conversion bushing for firewall 4.) Late style engine bar 5.) Late style engine bar mounts 6.) Late style motor mounts 7.) Late style engine mounts Generally, #1, #2, #4, #5, #7 you purchase from a non-members who are parting a cars. #3 and #6 you get from parts houses. |
Brad Roberts |
Jul 30 2006, 11:42 PM
Post
#6
|
914 Freak! Group: Members Posts: 19,148 Joined: 23-December 02 Member No.: 8 Region Association: None |
Dror,
do you have a digital camera? It would be easier for us to tell you what you might need based on the pictures. B |
914 dror |
Jul 31 2006, 12:16 AM
Post
#7
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
Are you really in Israel? Do you need part numbers? or parts? B Yes Sirr I am really in ISRAEL (IMG:style_emoticons/default/ar15.gif) Are you really in U.S.A? Really? :shades My 914 is suffering from 35 years of malpractice, lack of parts and poor mechanics So yes I do need parts and any thing I need must come from over seas and there is allot of red type involved in bringing it in through customs. But I’m a bit (IMG:style_emoticons/default/mueba.gif) so I will put her back on the Israeli roads dror |
914 dror |
Jul 31 2006, 12:24 AM
Post
#8
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
How many 914's in your neck of the woods? Keep your head down and (IMG:style_emoticons/default/welcome.png) Tanks for the welcoming, i`m happy to be here. My head is always raised! I’m not the kind of guy to take cover. |
914 dror |
Jul 31 2006, 12:41 AM
Post
#9
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
Dror, do you have a digital camera? It would be easier for us to tell you what you might need based on the pictures. B Yes I do have one, as for right now my home pc is dead. And I can’t upload files in to my office pc, but I’ll get that fixed soon and then I’ll show you my pride and joy. dror |
alpha434 |
Jul 31 2006, 02:14 AM
Post
#10
|
My member number is no coincidence. Group: Members Posts: 3,154 Joined: 16-December 05 From: Denver, CO Member No.: 5,280 Region Association: Rocky Mountains |
If he had #1 then why would he bother with converting the other?
Another thing is that you can do a cable shifter pretty easy on a tail. |
914 dror |
Jul 31 2006, 03:19 AM
Post
#11
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
If he had #1 then why would he bother with converting the other? Another thing is that you can do a cable shifter pretty easy on a tail. The car had been originally a tail sifter but some owner along the time (one of 14 previous owners (IMG:style_emoticons/default/icon_bump.gif) ) replaced it with a side shifter and it worked but not too good. I know side shifters are better, but I need the conversion to be done right. dror |
914 dror |
Jul 31 2006, 04:02 AM
Post
#12
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
1st .......SEARCH The components required have been discussed many times. But.....here you go: 1.) Sideshift tranny 2.) Sideshift shifter, front bar, rear bar 3.) Conversion bushing for firewall 4.) Late style engine bar 5.) Late style engine bar mounts 6.) Late style motor mounts 7.) Late style engine mounts Generally, #1, #2, #4, #5, #7 you purchase from a non-members who are parting a cars. #3 and #6 you get from parts houses. Dammm! I just spent 3 hour of my employer’s money to search for a good thread (one with show and tell) about doing the conversion - and no luck. Can you direct me? Please? (IMG:style_emoticons/default/chowtime.gif) |
SLITS |
Jul 31 2006, 06:44 AM
Post
#13
|
"This Utah shit is HARSH!" Group: Benefactors Posts: 13,602 Joined: 22-February 04 From: SoCal Mountains ... Member No.: 1,696 Region Association: None |
1st .......SEARCH The components required have been discussed many times. But.....here you go: 1.) Sideshift tranny 2.) Sideshift shifter, front bar, rear bar 3.) Conversion bushing for firewall 4.) Late style engine bar 5.) Late style engine bar mounts 6.) Late style motor mounts 7.) Late style engine mounts Generally, #1, #2, #4, #5, #7 you purchase from a non-members who are parting a cars. #3 and #6 you get from parts houses. Dammm! I just spent 3 hour of my employer’s money to search for a good thread (one with show and tell) about doing the conversion - and no luck. Can you direct me? Please? (IMG:style_emoticons/default/chowtime.gif) Since I told you to search...I will take images of the various components and post them. It may take me a couple of days. |
rick 918-S |
Jul 31 2006, 08:08 AM
Post
#14
|
Hey nice rack! -Celette Group: Members Posts: 20,503 Joined: 30-December 02 From: Now in Superior WI Member No.: 43 Region Association: Northstar Region |
|
Root_Werks |
Jul 31 2006, 09:13 AM
Post
#15
|
Village Idiot Group: Members Posts: 8,338 Joined: 25-May 04 From: About 5NM from Canada Member No.: 2,105 Region Association: Pacific Northwest |
Cool (IMG:style_emoticons/default/welcome.png)
|
r_towle |
Jul 31 2006, 09:41 AM
Post
#16
|
Custom Member Group: Members Posts: 24,591 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States |
Its really pretty simple as far as the parts go.
But to explain a bit. Remove your old engine/tranny once its out, remove the tranny..you can re-use the pressure plate and clutch disck, but now is a great time to replace them if you have any doubts. Now, on the front of the motor, the fan shroud needs to come off (Its easier to see everything this way) you need to unbolt the motor mount bar from the motor, this bar only works with the tail shifter. Once the fan shorud is off, and you have the new motor mounts, and brackets in hand, you will see the holes in the case, on either side of the oil pump...this is where the motor mount brakets go. the brakets bolt to the case, use locktight on these bolts,,,they are very hard to get to later... On the bracket goes the rubber motor mounts, these should be new mounts... On the rubber mounts goes the motor bar... now re-fit the fan shroud. Now, the shifter. What you need for this is all of the shifter linkage, front to back including the actual shifter itself, this is all a bit different... So, remove all the shifter linkage from the tail shifter, and inside the cabin, remove the shifter. now, the motor is still out of the car... on the firewall, there is a bushing that the old shifter rod went through...get a screw driver and pry it out...its not easy...but it will bend if you work at it...try to bend the bushing and not the surrounding metal... The new bushing is really hard to put in..I boil it, in really hot water..it makes the plastic a bit more bendy, but only for a few miutes...so you may need gloves for this... In any event... after you get the new bushing installed, you will probably hate your car and hate the idea of changing this to a side shifter...but that is really the worst part...that bushing... The rest is simple...with the engine still removed, slide the shifter bar into the cabin, the short bar...one end of it will have a hold in it..that end faces the motor.. you can install the shifter now...it makes it easier to get everthing together in the following steps... Now, install the new transmission on the motor..get all the muffler parts all bolts back in. Re-install the motor and tranny together. Once that is done, you take the rear shifter bar, and with the car raised up in the rear, you can feed the shifter bar through the motor mount bar from the front of the car, ind slide it into the shifter housing on the tranny. The hard part is getting the front bar into the rear bar...i use two people here... One person is pushing the shifter inside the car so that the inner bar is pushing back rearwards...the second person is under the car, pushing the rear bar forward...they slip together ok, if they are clean... there is an allen screw that only fits in one spot...install that when it all lines up... In the rear of the bar...you need to install the cup pivot assembly... this also has an allen screw that fits in only one spot...so tap and twist till it all lines up...then screw it in.. NOTE..these allen screws tend to back out over time...so more locktight here is the right thing to do... so, youare almost done... You just need to align your shifter so you can get to all the shift gates... I tend to do this, drive , then do it some more... bring a set of vise grips, and a 13mm socket on an extension with you while you drive.. Between the seats, near the firewall there is a small cover on top of the tunnel...remove it... I grab the shifter bar with the vise grips to hold it still...then loosen the 13mm nut that attaches the shifter to the bar..with the shifter handle and the vise grips, you can twist, and slide in and out on the bar till it all works perfect..then drive, do it again,,till you can get to every gear.. Good luck Rich |
914 dror |
Aug 1 2006, 12:52 AM
Post
#17
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
Since I told you to search...I will take images of the various components and post them. It may take me a couple of days. [/quote] Thanks again i realy need to see some photos so i`ll know what parts i can still use and what parts i need to look for. (IMG:style_emoticons/default/smile.gif) |
914 dror |
Aug 1 2006, 01:05 AM
Post
#18
|
Member Group: Members Posts: 67 Joined: 24-July 06 From: ISRAEL Member No.: 6,495 |
Its really pretty simple as far as the parts go. But to explain a bit. Remove your old engine/tranny once its out, remove the tranny..you can re-use the pressure plate and clutch disck, but now is a great time to replace them if you have any doubts. Now, on the front of the motor, the fan shroud needs to come off (Its easier to see everything this way) you need to unbolt the motor mount bar from the motor, this bar only works with the tail shifter. Once the fan shorud is off, and you have the new motor mounts, and brackets in hand, you will see the holes in the case, on either side of the oil pump...this is where the motor mount brakets go. the brakets bolt to the case, use locktight on these bolts,,,they are very hard to get to later... On the bracket goes the rubber motor mounts, these should be new mounts... On the rubber mounts goes the motor bar... now re-fit the fan shroud. Now, the shifter. What you need for this is all of the shifter linkage, front to back including the actual shifter itself, this is all a bit different... So, remove all the shifter linkage from the tail shifter, and inside the cabin, remove the shifter. now, the motor is still out of the car... on the firewall, there is a bushing that the old shifter rod went through...get a screw driver and pry it out...its not easy...but it will bend if you work at it...try to bend the bushing and not the surrounding metal... The new bushing is really hard to put in..I boil it, in really hot water..it makes the plastic a bit more bendy, but only for a few miutes...so you may need gloves for this... In any event... after you get the new bushing installed, you will probably hate your car and hate the idea of changing this to a side shifter...but that is really the worst part...that bushing... The rest is simple...with the engine still removed, slide the shifter bar into the cabin, the short bar...one end of it will have a hold in it..that end faces the motor.. you can install the shifter now...it makes it easier to get everthing together in the following steps... Now, install the new transmission on the motor..get all the muffler parts all bolts back in. Re-install the motor and tranny together. Once that is done, you take the rear shifter bar, and with the car raised up in the rear, you can feed the shifter bar through the motor mount bar from the front of the car, ind slide it into the shifter housing on the tranny. The hard part is getting the front bar into the rear bar...i use two people here... One person is pushing the shifter inside the car so that the inner bar is pushing back rearwards...the second person is under the car, pushing the rear bar forward...they slip together ok, if they are clean... there is an allen screw that only fits in one spot...install that when it all lines up... In the rear of the bar...you need to install the cup pivot assembly... this also has an allen screw that fits in only one spot...so tap and twist till it all lines up...then screw it in.. NOTE..these allen screws tend to back out over time...so more locktight here is the right thing to do... so, youare almost done... You just need to align your shifter so you can get to all the shift gates... I tend to do this, drive , then do it some more... bring a set of vise grips, and a 13mm socket on an extension with you while you drive.. Between the seats, near the firewall there is a small cover on top of the tunnel...remove it... I grab the shifter bar with the vise grips to hold it still...then loosen the 13mm nut that attaches the shifter to the bar..with the shifter handle and the vise grips, you can twist, and slide in and out on the bar till it all works perfect..then drive, do it again,,till you can get to every gear.. Good luck Rich Thank Rich I’m gonna print this and it would be of use when I’ll do the job, one thing though it is not a simple conversion cause I didn’t have the old setup and I don't know what exactly I do have here (some of the stuff is improvised). where would you buy the bushings and rubber seals and the mounts? dror |
GeorgeRud |
Aug 1 2006, 10:26 AM
Post
#19
|
Advanced Member Group: Members Posts: 3,725 Joined: 27-July 05 From: Chicagoland Member No.: 4,482 Region Association: Upper MidWest |
Pelican Parts, Perfomance Products, Automobile Atlanta ( I believe they still sell a kit to do the entire conversion), Mid America Motorworks all should have any bushings, etc. available.
|
Dr Evil |
Aug 1 2006, 10:39 AM
Post
#20
|
Send me your transmission! Group: Members Posts: 23,002 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region |
GPR at www.gprparts.com, call them as everything will not be on their site. Dave can help you.
|
Lo-Fi Version | Time is now: 16th June 2024 - 07:07 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |