 Reverse light switch / wires, Anyone have a pic? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Hammy |
 Dec 28 2006, 10:16 PM
Post
#1
|
|
mr. Wonderful  Group: Members Posts: 1,826 Joined: 20-October 04 From: Columbia, California Member No.: 2,978 Region Association: Northern California  |
I'm looking for a pic of the reverse light switch and the wires that connect to it. And to where it goes on the relay board. Anyone have one?
After my engine transfer I can't seem to remember where they hook up. I don't have any hanging wires or anything. Maybe it was on my old harness? I'm hoping I can just use some regular electrical wire and rig it up to work. Any help ? Thanks |
   |
 
|
| ws91420 |
Dec 28 2006, 10:30 PM
Post
#2
|
|
Yes I have one a Lensley 914 Group: Members Posts: 2,063 Joined: 10-September 03 From: Ruther Glen,VA (halfway between sticks and civilization) Member No.: 1,137 Region Association: MidAtlantic Region |
IIRC it comes down with the wires to the starter. Just has two little bullet connectors that plug in.
|
|
|
|
| GeorgeRud |
Dec 28 2006, 11:26 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,725 Joined: 27-July 05 From: Chicagoland Member No.: 4,482 Region Association: Upper MidWest |
Don't have a picture, but the switch is on the driver's side just below and behind the CV joint drive axle. The wires go up to the back relay board connector, and should be in the same wiring harness that goes to the starter. Both are brown if I remember right and can be connected either way, they simply complete a connection to turn on the reverse lights.
|
|
|
|
| Hammy |
Dec 29 2006, 03:33 PM
Post
#4
|
|
mr. Wonderful Group: Members Posts: 1,826 Joined: 20-October 04 From: Columbia, California Member No.: 2,978 Region Association: Northern California |
Can I just use some spare bullet connectors off my spare harness and mock the wires up to work?
|
|
|
|
| GeorgeRud |
Dec 29 2006, 06:09 PM
Post
#5
|
|
Advanced Member Group: Members Posts: 3,725 Joined: 27-July 05 From: Chicagoland Member No.: 4,482 Region Association: Upper MidWest |
Shouldn't be a problem, but look carefully in the area of the starter that you don't have the wires to that location at least. Otherwise, you could simply run the two wires from the switch up past the starter, through the engine sheetmetal, along the harness to the back relay panel connector. You should be able to find which location the wires go to by looking for the two brown wires (the connector top snaps off if you're carefull). Hopefully, if you have nothing else, you at least have the wires connected at the connector, it is a pain to try to solder the individual small connectors at that end.
|
|
|
|
| watsonrx13 |
Dec 29 2006, 06:14 PM
Post
#6
|
|
Advanced Member Group: Members Posts: 2,734 Joined: 18-February 03 From: Plant City, FL Member No.: 312 Region Association: South East States |
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th May 2024 - 05:58 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.