 CV joint dis-assembly, re-assembly..pictures enclosed, please add info or critic the instructions :) |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Mueller |
 Jan 14 2007, 01:17 AM
Post
#1
|
|
914 Freak!  Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None 
 |
follow the red spots..pay attention to the how the "point" goes to the "wide" section of the mating part.
starting at the top picture, if both hands are on the CV at the 9 and 3 o'clock postion, your fingers on your left hand would be pushing "up" while your thumb on the right hand would be pushing down. When the middle section is about 90° to it's original postion, it will slide right out (with a little help, but not much) reassembly is reverse...  |
   |
 
|
| So.Cal.914 |
Jan 14 2007, 01:23 AM
Post
#2
|
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
Very Cool, Thanks. It's one for my '914 maintainance info' folder
|
|
|
|
| swood |
Jan 14 2007, 01:30 AM
Post
#3
|
|
Senior Member Group: Members Posts: 1,839 Joined: 6-February 03 From: Strong Beach Member No.: 251 Region Association: None |
Thanks again.
Is there an assembly of the driveshaft thread anywhere? I've started a "how to not..." thread on my own. I know it's simple, but I've never done it before. |
|
|
|
| Aaron Cox |
Jan 14 2007, 01:31 AM
Post
#4
|
|
Professional Lawn Dart Group: Retired Admin Posts: 24,541 Joined: 1-February 03 From: OC Member No.: 219 Region Association: Southern California |
MIKE...
thanks for taking the time to do the step by step pics... your an asset to the community AA |
|
|
|
| Mueller |
Jan 14 2007, 01:39 AM
Post
#5
|
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None
|
QUOTE(Aaron Cox @ Jan 13 2007, 11:31 PM)  MIKE... thanks for taking the time to do the step by step pics... I'm just too much of a wuss to go out in the garage and work on my...it if f'n could out there (IMG:style_emoticons/default/wacko.gif) AA |
|
|
|
| neo914-6 |
Jan 14 2007, 01:44 AM
Post
#6
|
|
neo life Group: Members Posts: 5,086 Joined: 16-January 03 From: Willow Glen (San Jose) Member No.: 159 |
Hey Mike,
How did you clean the grease off them? |
|
|
|
| swood |
Jan 14 2007, 01:47 AM
Post
#7
|
|
Senior Member Group: Members Posts: 1,839 Joined: 6-February 03 From: Strong Beach Member No.: 251 Region Association: None |
They was new.
|
|
|
|
| McMark |
Jan 14 2007, 02:44 AM
Post
#8
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
|
|
|
|
| Allan |
Jan 14 2007, 09:43 AM
Post
#9
|
|
Teenerless Weenie Group: Members Posts: 8,373 Joined: 5-July 04 From: Western Mesopotamia Member No.: 2,304 Region Association: Southern California |
Hey Mike, check your PM's... (IMG:style_emoticons/default/biggrin.gif)
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th May 2024 - 11:38 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.