 Megasquirt question.... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Joe Bob |
 Feb 6 2007, 08:59 AM
Post
#1
|
|
Retired admin, banned a few times  Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None  |
If you are running dual throttle bodies...where can you put a "fifth" injector for cold start enrichment or is there a setting in the software I'm missing? My 2.2 runs like crap until 210F.....which is about 5 miles at cruising speed.
|
   |
 
|
Posts in this topic
mikez Megasquirt question.... Feb 6 2007, 08:59 AM
DNHunt Mike
Why would you need a fifth injector unless t... Feb 6 2007, 09:10 AM mikez OK...I'll try that. The injectors are what ca... Feb 6 2007, 09:58 AM DNHunt Mike
Are you familiar with the sreen that has the... Feb 6 2007, 10:57 AM
mikez
Mike
Are you familiar with the sreen that has th... Feb 6 2007, 11:58 PM jkeyzer 5th injectors are for outdated 70s analog fuel inj... Feb 6 2007, 11:30 AM crash914 richen the hell out of it at low temps...head temp... Feb 7 2007, 06:58 AM mikez No problem on starting....just during engine oil w... Feb 7 2007, 08:28 AM DNHunt Mike
I don't think there is a problem using t... Feb 7 2007, 08:45 AM toon1 MS also has "easy therm" it is a progra... Feb 7 2007, 09:28 AM DNHunt
MS also has "easy therm" it is a progr... Feb 7 2007, 09:36 AM restore2seater This may help with calibration.
DIY Auto Tune Feb 7 2007, 10:38 AM ischmitz O.K.,
I will richen up the table for warm-up on Mi... Feb 8 2007, 07:03 AM smdubovsky Got ITBs on my 911. No easy way to add air for id... Feb 8 2007, 12:51 PM banger I thought on some of the 80s chevy cars, they had ... Feb 8 2007, 02:08 PM messix add advance below desired idle is the way to go. Feb 8 2007, 02:46 PM Aaron Cox
add advance below desired idle is the way to go.
... Feb 8 2007, 04:51 PM crash914 the table burn problem sounds like a communication... Feb 8 2007, 04:43 PM Crazyhippy Just added 25* to mine, no problem cranking...
Pu... Feb 8 2007, 05:23 PM ischmitz I found that too much advance below your target id... Feb 8 2007, 05:29 PM messix you only need a couple of degrees. dn hunt had his... Feb 8 2007, 07:23 PM TimT Cranking rpm is usually around 250-300 rpm, and t... Feb 8 2007, 08:05 PM mikez Usual cranking requires throtle manipulation....wh... Feb 8 2007, 08:14 PM TimT
correctamundo....having to manipulate the throt... Feb 8 2007, 08:51 PM DNHunt There is adjustment for prime pulse, cranking enri... Feb 9 2007, 08:08 AM jhadler Can't speak to the FI enrichment techniques, t... Feb 9 2007, 05:44 PM mikez Did some changes as suggested....runs a LOT better... Feb 9 2007, 10:11 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th May 2024 - 08:10 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.