 Inner cv came completely off of the trans output flange, a mile or so from home. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Gint |
 May 10 2007, 07:47 PM
Post
#41
|
|
Mike Ginter  Group: Admin Posts: 16,075 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains   |
Just when you get the thing running great... bam! CV joint comes off! Completely seperated from the trans output flange. I rolled it all the way home to just around the corner from my house. Shar helped me push it from there to the street in front of the driveway. Danny's due over in a few and together with help from my youngest son and Shar, we can get it up the driveway and onto the side of the house.
I got lucky in that the shaft just fell down on top of the HE and didn't do any damage. Pics later... |
   |
 
|
Posts in this topic
Gint Inner cv came completely off of the trans output flange May 10 2007, 07:47 PM
Eric_Shea Got yer back... May 10 2007, 07:49 PM TROJANMAN I 've got a spare set of axles with CV's o... May 10 2007, 07:50 PM Pat Garvey
Just when you get the thing running great... bam... May 10 2007, 07:51 PM Cap'n Krusty Repeat after me: "New bolts, new washers, pr... May 10 2007, 08:11 PM
SirAndy
you have my permission to clean the jount and fla... May 10 2007, 08:26 PM So.Cal.914 At least you weren't under it. May 10 2007, 08:32 PM Gint
At least you weren't under it.
But I will be ... May 10 2007, 09:39 PM majkos
At least you weren't under it.
But I will be... May 10 2007, 09:52 PM type47fan . . . somebody needs Dr. Evil's magic CV joint... May 10 2007, 08:33 PM 914Sixer Back in 1971 I did a clutch job on my 67 911S. I... May 10 2007, 08:49 PM Ferg Was there swearing involved :confused: :chairfal... May 10 2007, 09:50 PM Dr Evil DOH! You have developed the fecal touch. Every... May 10 2007, 09:57 PM jkeyzer CV failure is a rite of passage for the 914 owner.... May 10 2007, 10:47 PM Cap'n Krusty
CV failure is a rite of passage for the 914 owner... May 10 2007, 10:54 PM ClayPerrine
CV failure is a rite of passage for the 914 owne... May 11 2007, 10:10 AM John
[quote name='Cap'n Krusty' post='899111' date... May 11 2007, 10:23 AM Gint Just for reference, what is the torque spec?
Acco... May 11 2007, 10:27 AM John
Just for reference, what is the torque spec?
Acc... May 11 2007, 10:57 AM rick 918-S
[quote name='Cap'n Krusty' post='899111' dat... May 11 2007, 10:40 AM Gint Preliminary investigation by just reaching under t... May 11 2007, 10:23 AM John
Preliminary investigation by just reaching under ... May 11 2007, 10:29 AM Gint I'll put the joint back on with the two good b... May 11 2007, 10:35 AM McMark Cap'N do you pay any special attention to tryi... May 11 2007, 10:36 AM John Need an output flange (without goobered threads) t... May 11 2007, 10:38 AM Gint
Need an output flange (without goobered threads) ... May 11 2007, 10:39 AM davep It could be that the bolts won't start because... May 11 2007, 10:42 AM Gint
It could be that the bolts won't start becaus... May 11 2007, 10:45 AM MrKona
[quote name='Gint' post='899230' date='May 11 200... May 11 2007, 11:14 AM byndbad914 I haven't had a CV come off either. Let you g... May 11 2007, 11:16 AM Dr Evil Gint, just pull the flange. Its stoopid easy and w... May 11 2007, 11:34 AM Gint
Gint, just pull the flange. Its stoopid easy and ... May 11 2007, 12:55 PM RoninEclipse2G same thing happened to my wife in the creamsicle m... May 11 2007, 12:18 PM eric914 Did the gasket brake right through the middle? Ta... May 11 2007, 12:31 PM Gint The 914 is on the lift. Root cause analysis is co... May 11 2007, 02:16 PM MoveQik Welcome to the club!! :-)
Safety wires sh... May 11 2007, 02:22 PM Ferg Time to put Dr Evils kit to work...
You have ti... May 11 2007, 02:33 PM Gint Safety wiring CV bolts is simply not required if t... May 11 2007, 02:38 PM Travis Neff 29 to 31 ft/lbs May 11 2007, 03:06 PM RoninEclipse2G we installed them "correctly" twice now ... May 11 2007, 03:11 PM Gint If you use a tap Ron, they will end up even more l... May 11 2007, 04:54 PM kwales Sometimes they just work loose over time.
Had a ... May 11 2007, 07:33 PM Dr. Roger Schoor washers are single use washers, aren't ... May 12 2007, 01:42 AM Gint
Schoor washers are single use washers, aren't... May 12 2007, 07:40 AM Dr Evil Yep, Schnorr washers are one time use as they are ... May 12 2007, 09:14 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 19th May 2024 - 09:45 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.