74 + 911 Rear Hubs for 5 Lug Conversion, spacer thickness |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
74 + 911 Rear Hubs for 5 Lug Conversion, spacer thickness |
jaxdream |
Jan 10 2009, 01:39 AM
Post
#1
|
Senior Member Group: Members Posts: 974 Joined: 8-July 08 From: North Central Tennessee Member No.: 9,270 Region Association: South East States |
Hi guys, I've been reading some of tyhe posts concerning using the 74 + hub centric eared 911 rear hubs for a 5 lug conversion. Iv'e seen mentioned that one needs to use a 5mm spacer on the hub on the wheel side against the outter inner bearing race . My question is why the 5mm spacer instead of a 6mm spacer ?? 914 and earlier 911 use a 36mm wide bearing the later mentioned 911 used a 42mm wide bearing , what happens with the leftover 1 mm?? Does it stick out to be sqished up against the stub , will it not allow the hub / stub to fully seat ??As i have figured on using the inner races from the aforementioned 74+ hub bearing having them ground down on a surface grinder for squareness sake , just want to be sure of the thickness demention before the grinding to get the right thickness I need.
Jaxdream (IMG:style_emoticons/default/confused24.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/unsure.gif) |
hcdmueller |
Feb 21 2009, 06:39 AM
Post
#41
|
????????????? Group: Members Posts: 542 Joined: 4-February 06 From: UK Member No.: 5,527 Region Association: England |
I was just about to ask again. I am still in for a set.
|
strawman |
Feb 21 2009, 06:09 PM
Post
#42
|
Senior Member Group: Members Posts: 881 Joined: 25-January 08 From: Los Osos, CA Member No.: 8,624 Region Association: Central California |
Hi Paul --
I need a set, too. I'm just down the hill from you (I'm in Davis), so I could come pick up my set. Of course, that would permit me to drool over your car again!!! Geoff |
PRS914-6 |
Feb 21 2009, 06:42 PM
Post
#43
|
Excellence Magazine Project 914 3.6 Group: Retired Members Posts: 1,278 Joined: 20-May 06 From: Central California Member No.: 6,031 Region Association: None |
Sorry I have not got to them yet. Anyone that knows me is aware that I am a ski freak and I have had a guest from Switzerland here for the last 10 days showing him California skiing. Should be able to get to them this week....Sorry for the delay
Sorry Geoff, We'll have to put tape over your mouth if you are gonna drool on my paint (IMG:style_emoticons/default/drooley.gif) |
Eric_Shea |
Feb 21 2009, 06:54 PM
Post
#44
|
PMB Performance Group: Admin Posts: 19,278 Joined: 3-September 03 From: Salt Lake City, UT Member No.: 1,110 Region Association: Rocky Mountains |
QUOTE I am a ski freak Then you'll just have to deliver them yourself. (IMG:style_emoticons/default/wink.gif) |
PRS914-6 |
Mar 2 2009, 12:41 PM
Post
#45
|
Excellence Magazine Project 914 3.6 Group: Retired Members Posts: 1,278 Joined: 20-May 06 From: Central California Member No.: 6,031 Region Association: None |
Just an update......I had to order the steel for the spacers but it has arrived in Sacramento. I should get it today or tomorrow and have them finished a few days later.....sorry for the delay
|
strawman |
Mar 2 2009, 07:29 PM
Post
#46
|
Senior Member Group: Members Posts: 881 Joined: 25-January 08 From: Los Osos, CA Member No.: 8,624 Region Association: Central California |
Kewl! PM me when they're done so I can drive up the hill to pick 'em up. You going to Taco Tuesday in Elk Grove tomorrow evening?
Geoff Just an update......I had to order the steel for the spacers but it has arrived in Sacramento. I should get it today or tomorrow and have them finished a few days later.....sorry for the delay |
hcdmueller |
Mar 3 2009, 01:43 AM
Post
#47
|
????????????? Group: Members Posts: 542 Joined: 4-February 06 From: UK Member No.: 5,527 Region Association: England |
I will be away from the internet for the next few weeks. I still want a set. PM me when they are done and I will get the payment to you when I get back online.
|
PRS914-6 |
Mar 5 2009, 06:36 PM
Post
#48
|
Excellence Magazine Project 914 3.6 Group: Retired Members Posts: 1,278 Joined: 20-May 06 From: Central California Member No.: 6,031 Region Association: None |
I have 8 sets of spacers made. $25.00 + $5.00 for a padded envelope, postage and Paypal fees for USA deliveries. Just Paypal me and I'll ship them out. You can Paypal me at paul@sayegh.org and please tell me your 914World name so I can keep track. Those that showed interest above will get priority.
When you install them make sure the chamfered side goes against the radius on the hubs and the flat side against the bearing. Pretty obvious but don't want any disasters. |
charliew |
Mar 5 2009, 08:53 PM
Post
#49
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
Thanks Paul, pp sent
|
hcdmueller |
Mar 6 2009, 08:41 AM
Post
#50
|
????????????? Group: Members Posts: 542 Joined: 4-February 06 From: UK Member No.: 5,527 Region Association: England |
Good timing for me. I am off the grid on monday. Paypal Sent.
|
strawman |
Mar 7 2009, 04:49 PM
Post
#51
|
Senior Member Group: Members Posts: 881 Joined: 25-January 08 From: Los Osos, CA Member No.: 8,624 Region Association: Central California |
Money (via Paypal) and PM sent. Thanks for helping with this, Paul!
Geoff |
BIGKAT_83 |
Mar 7 2009, 05:58 PM
Post
#52
|
Senior Member Group: Members Posts: 1,798 Joined: 25-January 03 From: Way down south Bogart,GA Member No.: 194 Region Association: South East States |
|
PRS914-6 |
Mar 10 2009, 11:26 AM
Post
#53
|
Excellence Magazine Project 914 3.6 Group: Retired Members Posts: 1,278 Joined: 20-May 06 From: Central California Member No.: 6,031 Region Association: None |
Charles, Christopher, Robert and Geoffrey, your spacers shipped this AM.
4 sets left. |
jimsfolly |
Mar 11 2009, 11:57 PM
Post
#54
|
Newbie Group: Members Posts: 17 Joined: 15-June 08 From: Renton, WA Member No.: 9,174 Region Association: None |
|
Richard Casto |
Mar 12 2009, 06:45 AM
Post
#55
|
Blue Sky Motorsports, LLC Group: Members Posts: 1,465 Joined: 2-August 05 From: Durham, NC Member No.: 4,523 Region Association: South East States |
4 sets left. Paul, Payment sent via paypal for one set just a few minutes ago. Just let me know if I am too late for one of the four left. FYI.. My screen name and my real name are one in the same. (IMG:style_emoticons/default/wink.gif) Richard |
jaxdream |
Mar 12 2009, 02:06 PM
Post
#56
|
Senior Member Group: Members Posts: 974 Joined: 8-July 08 From: North Central Tennessee Member No.: 9,270 Region Association: South East States |
Paul , it seems that I have stirred up some buisness for you . (IMG:style_emoticons/default/stirthepot.gif) I got a set from one of the mtrsports compys not gonna slam them , heck anybody can turn out a off spec product every now and then, just rather disappointed -5.87 mm on one side 5.07 mm on the other - will not use , just gonna put em up , restoking fee 25% not worth return and hassle. Keep em coming !!! (IMG:style_emoticons/default/piratenanner.gif)
Jaxdream |
PRS914-6 |
Mar 14 2009, 01:58 PM
Post
#57
|
Excellence Magazine Project 914 3.6 Group: Retired Members Posts: 1,278 Joined: 20-May 06 From: Central California Member No.: 6,031 Region Association: None |
Richard and James, your spacers were shipped today. My response will be better when ski season is over. (IMG:style_emoticons/default/smile.gif)
Erik, you had wanted 3 sets and Mel wanted one. No payment from either so the last 2 sets available to anyone who needs\wants them. |
Lo-Fi Version | Time is now: 1st June 2024 - 01:44 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |