 100mm output flange., Questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| PeeGreen 914 |
 Jan 14 2009, 04:23 PM
Post
#1
|
|
Just when you think you're done...wait, there is more..lol  Group: Members Posts: 10,219 Joined: 21-September 06 From: Seattle, WA... actually Everett Member No.: 6,884 Region Association: Pacific Northwest 
 |
So I need to get some 100mm output flanges to go with my 944 axles I want to use on my 914. I am thinking they come out of a 915. What do I really need to look for with my 901 box and is the 100mm measured from the bolt spacing or the distance across or?
I also was asked if I need coarse or fine spline. Ummmm.... 901 guys help me out here. Dr. Evil? Slits? anyone? |
   |
 
|
Posts in this topic
Phoenix 914-6GT 100mm output flange. Jan 14 2009, 04:23 PM
Phoenix 914-6GT :confused: Jan 14 2009, 11:57 PM SirAndy Coarse spline from a late '70ies 915 tranny ..... Jan 15 2009, 12:09 AM
Phoenix 914-6GT
Coarse spline from a late '70ies 915 tranny .... Jan 15 2009, 12:15 AM SirAndy
Coarse spline from a late '70ies 915 tranny ... Jan 15 2009, 12:31 AM Phoenix 914-6GT Thanks Andy :D :beer2: Jan 15 2009, 12:38 AM zig-n-zag 100mm cv output flanges on the 923/02 tranny (912e... Jan 15 2009, 01:06 AM zig-n-zag The output flanges on the 1976 912e have a raised ... Jan 15 2009, 01:17 AM zig-n-zag I machined the 914 axles to accept the 944t cv... Jan 15 2009, 01:42 AM Phoenix 914-6GT I have everything I need other than the output fla... Jan 15 2009, 01:56 AM GS Guy If you can't find any factory stub axles, Todd... Jan 15 2009, 06:38 AM jd74914 You can call EASY too. I've gotten a few thing... Jan 15 2009, 08:19 AM Phoenix 914-6GT
You can call EASY too. I've gotten a few thin... Jan 15 2009, 10:37 AM Krieger914 I got two sets from Parts Heaven in Hayward. Try ... Jan 15 2009, 10:24 AM charliew I have some 901's and 914/901's for some b... Jan 15 2009, 11:48 AM SirAndy I run a stock 901 behind my 3.6L /6 ...
So far, s... Jan 15 2009, 12:04 PM charliew Does anyone know if vw bus cvs are as good as 944 ... Jan 15 2009, 01:02 PM Gary Jon,
I have a spare pair of 915 sporto output fla... Jan 15 2009, 01:47 PM Phoenix 914-6GT
Jon,
I have a spare pair of 915 sporto output fl... Jan 15 2009, 04:11 PM SirAndy
I believe the 944 axles are the perfect length
I ... Jan 15 2009, 05:41 PM mikez I have an early 915 at Steve Wiley's that we a... Jan 15 2009, 03:53 PM Phoenix 914-6GT Oh. Well, the guy I bought these from had been usi... Jan 15 2009, 06:44 PM SirAndy
Oh. Well, the guy I bought these from had been us... Jan 15 2009, 06:51 PM Aaron Cox I almost bought a set from OTTO a few years back, ... Jan 15 2009, 06:47 PM Phoenix 914-6GT He had them matted to a hot 3.2 and all was fine. ... Jan 15 2009, 06:55 PM Phoenix 914-6GT Turns out they are longer than the original axles.... Jan 20 2009, 12:56 AM SirAndy
Andy, any luck with Easy?
Finally had the time to... Jan 23 2009, 05:04 PM jaxdream 915 trans output flange # 923.332.209.02 coarse sp... Jan 20 2009, 10:04 PM Phoenix 914-6GT So are you going to do this as well or sell me the... Jan 20 2009, 10:50 PM jaxdream
So are you going to do this as well or sell me th... Jan 20 2009, 11:23 PM Phoenix 914-6GT email sent :beer2: Jan 20 2009, 11:37 PM Eric_Shea Just buy the proper length 28 spline axle from Swa... Jan 21 2009, 04:56 PM Phoenix 914-6GT Why would I do that when all I need now are the ou... Jan 21 2009, 05:07 PM Eric_Shea You're right... you should have done it a long... Jan 21 2009, 05:33 PM Phoenix 914-6GT <_< I know. I just never bothered until now ... Jan 21 2009, 11:12 PM Phoenix 914-6GT Why are people telling me the six bolt 100mm flang... Jan 22 2009, 03:22 PM SirAndy
Why are people telling me the six bolt 100mm flan... Jan 23 2009, 05:11 PM Eric_Shea Cause that's a 108 or someone drilled the nubs... Jan 22 2009, 03:35 PM Phoenix 914-6GT Really? So all I would need to do is drill the nub... Jan 22 2009, 03:38 PM Eric_Shea 1/2 joking with you. I do believe you can drill t... Jan 22 2009, 03:47 PM Phoenix 914-6GT
1/2 joking with you. I do believe you can drill ... Jan 23 2009, 11:46 AM Phoenix 914-6GT Thanks for checking for me Andy.
So anyone have... Jan 23 2009, 06:42 PM Eric_Shea
Is that a "Bro"? :blink:
Jon, check ... Jan 24 2009, 02:48 PM SirAndy Is that a "Bro"?
:pinkylifters: Jan 24 2009, 03:42 PM jaxdream As to what species he is ,doesn't concern me ,... Jan 24 2009, 04:46 PM Phoenix 914-6GT Species? Well Sir Andy is German if that is what y... Jan 24 2009, 08:00 PM SirAndy
I believe he is drilling to use the JWest linkage... Jan 24 2009, 09:03 PM Wilhelm Is the flange you are looking for is this:
91... Jan 25 2009, 10:53 AM sixnotfour Jon call monty.
As for DC Auto , I have been wai... Jan 25 2009, 11:13 AM SirAndy
If the flange you are looking for is this
No. He... Jan 25 2009, 01:51 PM Phoenix 914-6GT Just got a PM on the PP board from a guy just Nort... Jan 25 2009, 02:56 PM Wilhelm
Just got a PM on the PP board from a guy just Nor... Jan 25 2009, 03:31 PM Phoenix 914-6GT I will let you know. I sent him and email a few se... Jan 25 2009, 03:59 PM SirAndy Ayupp, those look right ... 100mm?
:) Andy Jan 25 2009, 04:06 PM Phoenix 914-6GT I found another set of these as well if someone is... Jan 25 2009, 05:30 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 18th May 2024 - 02:52 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.