Ok i would like to buy myself a new years present for the my six project....
I would like to buy a front cooler, 914-6 shroud, fan, lines, and tank with fittings for seting up a 3.0
recomendations on a engine bar would be great too...

Hey Karl where did you get your "stuff"
thanks guys, and off to work i go....
steve

Hey Steve (nice plane),
You can get some of the parts you want from Rich Johnson, or all from Patrick Motorsports if I'm not mistaken. Even the bar.
HTH

I went with a Fluidyne cooler and *highly* recommend them.
Summit Racing for lines & fittings.
Troutman for a thermostat.

Rich Johnson for a front mount.....don't even think about the rest of that cra....er.....stuff......that prolly offended several folks.

I agree with JP. The Fluidyne was highly recommended by the group. I bought mine from Hoerr Racing, Peoria, Il. 866 851 7223.
I chose the #DB30417, its a doubles pass, for 2x cooling.
All the connectors from Summit. The only difference is Mocal Themo., it was already on the car.
Where are you going to run your oil lines?

The teener is going to be run as a 2.0 for the next season but I am acumulating parts as we will be starting as soon as the cold weather hits in fall, i want to be sure that i have all the parts and peices lined up so the car is not a jackstand-queen the following spring. so I am not sure where i am running my lines as of yet... Hope to draw as much info as i can before making descisions...
All info is much appreciated....do any Club members run at the Mission track
cheers
steve

Mission Track , There is a guy , Frank that runs a 914-6 , he aquired from my friend Walt. I have been there 3 years for the
annual BC /sovren race. Unfortunately I have been there with a 67 427 Corvette roadster. Stars and stripes. Have you seen
it ? I quit that so I will have time for my 914-6 hope to run up there fun little track .
If you would like to get in touch with the local guy .
with the six let me Know I ll get his number from Walt.
Check the fluiddyne site for selection. Jeff

Any Ideas on the shroud and fan?? Or who to contact for the resevoir....aluminum or steel??
Thanks guys...
Merry ho-ho

You should contact Steve at AIRCOOLEDRACING.COM. His 914 was the one featured in Excellance this month. He has a new cooler for 914's and it sounds like a great one. I have bought parts from Steve and he ais great to work with and his knowledge of 914's is a great help.

Aircooled Racing & Parts
1560 Old Mountain Road, Wellsville, PA 17365 USA
Phone ( 717 ) 432-4116 Fax ( 717 ) 432-RACE
E-mail: info@aircooledracing.com

Aircooled Racing

Hope it helps,
Van914

QUOTE (pete-stevers @ Dec 25 2004, 04:53 PM)

Any Ideas on the shroud and fan??  Or who to contact for the resevoir....aluminum or steel??

I got my fiberglass two piece shroud from Getty Design.
They are the only source that I know of that includes both pieces.
Most places just have the shroud and not the bottom duct piece.
Also beware of the quality of other sources.
PMS resells the Getty two piece shroud.
For the fans I just used two 12v 4" computer fans with a thermostat from Pep boys.
The fans fit under the shroud and I also have a switch in the dash to force them on.
I bought the oil cooler and fittings from PMS.
They sell a SETRAB cooler that's small enough to fit in the shroud.
The modified mazda rx-7 cooler wouldn't fit in the shroud without cutting the shroud.

I think I will fab the shroud myself, What size lines will i need for the oil cooler if is use a fluidyne with a 3.0, and i run them along the outside of the longs, hope to buy from summit..., the oil tank from GPR....
is Rich Johnson a member? details are greatly appreciated....
steve peters

Richs stuff
http://www.914world.com/bbs2/index.php?act...t=ST&f=4&t=4319

Did you get the info about the BC six guy Frank W. ?