Cylinder Head Temperature Sensor install, Trying to install the CHT Sensor |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Cylinder Head Temperature Sensor install, Trying to install the CHT Sensor |
Keoni914 |
Jul 25 2009, 09:55 AM
Post
#1
|
Newbie Group: Members Posts: 35 Joined: 12-November 08 From: NorthEast PA Member No.: 9,746 Region Association: North East States |
I have a '72 1.7 that has a few problems. I have a 0 280 130 012 Cylinder Head Temperature Sensor that I would like to install but can't seem to figure out how.
It's near the #3 Cylinder, correct? Do I have to remove the intake? This newbie is stumped! (IMG:style_emoticons/default/hissyfit.gif) Can someone help me?? Thanks in advance! Keoni914 |
Dave_Darling |
Jul 25 2009, 03:00 PM
Post
#2
|
914 Idiot Group: Members Posts: 14,991 Joined: 9-January 03 From: Silicon Valley / Kailua-Kona Member No.: 121 Region Association: Northern California |
You don't have to remove the intake. You do have to find the correct hole in the engine tin and make sure the sensor is there.
You can thread a deep-well 13mm socket on the wire, fold up the wire in the socket, and remove that way. You can also strip the threads on the sensor that way. (IMG:style_emoticons/default/sad.gif) Big PITA, very very hard to repair without dropping the engine. A specialty tool that helps the R&R is a "tubular spanner", which is a hex-shaped metal tube that fits over the sensor and that you put a wrench over the other end. Or you can knock one corner off of a short extension so that it allows room for the sensor's wire when you plug the extension into the back of the 13mm socket. Whatever you use, hose it down with a lot of penetrating oil for a couple of days first. (WD-40 is not a penetrating oil; PB Blaster and Aero Kroyl are.) And pray. --DD |
Keoni914 |
Jul 25 2009, 04:27 PM
Post
#3
|
Newbie Group: Members Posts: 35 Joined: 12-November 08 From: NorthEast PA Member No.: 9,746 Region Association: North East States |
Dave thanks but...
Oh Oh so your saying getting the old out might be a PITA? From my perspective the hole looks like it's right in front of the intake, way too close for a deep socket. Am I looking in the right place? Anybody have photos? Darn, nothing is easy on a Teener, huh?? (IMG:style_emoticons/default/sawzall-smiley.gif) Keoni914 |
McMark |
Jul 25 2009, 04:30 PM
Post
#4
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
Deep socket with an extension will fit.
|
Dave_Darling |
Jul 25 2009, 06:24 PM
Post
#5
|
914 Idiot Group: Members Posts: 14,991 Joined: 9-January 03 From: Silicon Valley / Kailua-Kona Member No.: 121 Region Association: Northern California |
I never found getting it out to be that difficult. Getting it out without the threads coming with it can be a challenge, and trying to install a time-sert or other thread repair without dropping the motor.... That is the true PITA!
And the deep-well socket with an extension works well. You may even be able to use a non-deep socket if you use an extension with a corner ground off to make room for the wire. --DD |
wilchek |
Jul 25 2009, 06:33 PM
Post
#6
|
Senior Member Group: Members Posts: 506 Joined: 8-June 04 From: Eastern Pennsylvania Member No.: 2,177 |
This is what I did two years ago. I took the runners off and it was easy enough to get to. As I said in the post it is a little ways in the tin. I used a deep well 13mm socket. I ground off the edge of a cheap 2in extension so I could pull the wire thru. Beyond that it is not too bad. Look for the wire that goes into the tin thru a rubber grommet under the fuel injector intake runner on the passenger side.
http://www.914world.com/bbs2/index.php?sho...c=73201&hl= |
jimkelly |
Jul 26 2009, 04:34 PM
Post
#7
|
Delaware USA Group: Members Posts: 4,969 Joined: 5-August 04 From: Delaware, USA Member No.: 2,460 Region Association: MidAtlantic Region |
i can't find it - but - there is an awesome thread here somewhere that shows some of the tools guys here made for working on thier 914's - one tool is a custom socket with pics to install this sensor. dang - i manually searched 22 pages and could not find it : ((
|
McMark |
Jul 26 2009, 07:32 PM
Post
#8
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
|
jimkelly |
Jul 26 2009, 07:53 PM
Post
#9
|
Delaware USA Group: Members Posts: 4,969 Joined: 5-August 04 From: Delaware, USA Member No.: 2,460 Region Association: MidAtlantic Region |
thanks
i tried special and custom - duh : )) jim |
Lo-Fi Version | Time is now: 8th June 2024 - 12:29 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |