 Turbo Tie Rod Washers, Are they critical? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| vesnyder |
 Dec 22 2005, 05:04 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 680 Joined: 14-April 05 From: Cleveland, OH Member No.: 3,933  |
I just installed the turbo tie rods and did not install the washer that came with the kit that goes between the tie rod and the steering rack - are these needed?
(IMG:http://www.914world.com/bbs2/html/emoticons/headbang.gif) That's what I was afraid of!! They were a bitch to tighten and they will be impossible when I install the washer. |
   |
 
|
  |
Replies
| FourBlades |
Feb 2 2010, 09:38 PM
Post
#2
|
|
From Wreck to Rockin Group: Members Posts: 2,056 Joined: 3-December 07 From: Brevard, FL Member No.: 8,414 Region Association: South East States 
|
Mark, Thanks for all your insights on this! If you use a smaller diameter, thinner washer, is it then possible to crank the steering too far one way and run out of teeth on the rack, or is the end of the tie rod too big to go into the end of the rack? John |
|
|
|
Posts in this topic
vesnyder Turbo Tie Rod Washers Dec 22 2005, 05:04 PM
bondo Yes! They keep you fromn overextending (and de... Dec 22 2005, 05:09 PM TimT You need the washers. Without then you will never ... Dec 22 2005, 05:16 PM porsche914blue It seems some cars need them and others don't.... Dec 22 2005, 07:05 PM FourBlades Maybe someone knows the answer to this, or has the... Feb 1 2010, 03:13 PM type47 I thought the washers had something to do with ... Feb 1 2010, 03:42 PM McMark The washers aren't for bump steer. You need t... Feb 1 2010, 03:49 PM Eric_Shea I believe all spindle arms are not created equal. ... Feb 1 2010, 04:05 PM McMark Part #4 is on the stock steering rack and serves t... Feb 1 2010, 04:19 PM McMark Yup, the steering rack is a bar with teeth machine... Feb 1 2010, 04:23 PM
SirAndy
Yup, the steering rack is a bar with teeth machin... Feb 1 2010, 04:33 PM Eric_Shea
This is where I'm a tad confused. With a TT... Feb 1 2010, 06:02 PM McMark Nope, the TTR comes with a rubber block on the rod... Feb 1 2010, 06:15 PM Eric_Shea Ahhhh... that's the part I forgot. Feb 1 2010, 06:56 PM jaxdream I installed a set of the Lenforders ( spelling ) a... Feb 1 2010, 11:36 PM craig downs I was told that the spacers are for if your using ... Feb 2 2010, 12:56 AM kconway
I was told that the spacers are for if your using... Feb 2 2010, 09:33 AM PRS914-6 I used 911 struts AND steering rack. The washers ... Feb 2 2010, 10:26 AM Eric_Shea At this point it would be nice to do a strut compa... Feb 2 2010, 10:36 AM PRS914-6 I'm using the Koni's as well......no issue... Feb 2 2010, 11:04 AM FourBlades :popcorn: :popcorn: :popcorn: Feb 2 2010, 12:17 PM McMark A thin washer will work just fine. Also note that... Feb 2 2010, 02:00 PM McMark The thin washers pictured above have the same OD a... Feb 2 2010, 10:48 PM 914Sixer I will try and get a picture later today. The sto... Feb 3 2010, 11:40 AM Eric_Shea
That's one of the obvious visual differences... Feb 3 2010, 03:56 PM McMark '69 T Struts. Feb 3 2010, 04:13 PM kconway I believe this to be a 911T strut I'm putting ... Feb 4 2010, 12:20 AM Gint BTW, is there a special type of grease to use on t... Feb 4 2010, 09:20 AM Eric_Shea It would be nice to lay them on their backs, each ... Feb 4 2010, 08:35 AM Eric_Shea I don't really think it matters.
The factor... Feb 4 2010, 11:39 AM 914Sixer Here is a picture of a 75 911 Boge and 73 914 Bils... Feb 4 2010, 01:18 PM FourBlades Well maybe it is only the early 911 struts that ar... Mar 20 2010, 08:23 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 09:29 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.