![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
914_7T3 |
![]()
Post
#1
|
Please forgive me, I'm new to all of this! ![]() ![]() ![]() Group: Members Posts: 1,875 Joined: 3-April 17 From: Los Angeles, CA Member No.: 20,991 Region Association: Southern California ![]() ![]() |
I have been on 914 World for just a few weeks and with the knowledge and support of everyone was able to get up to speed quickly on values and things to look out for. when considering a vehicle to purchase.
I just acquired this matching numbers '73 Marathon Blue 2.0 up in NorCal on Wednesday. Straight car with a strong motor and minimal rust issues. Fuel lines and pump have already replaced and rear suspension and brakes were done about 5,000 miles ago back in 2012. The required rust repairs of significance will entail a partial front trunk pan and minor hell hole repair so in the grand scheme of things a great starting point. My plan is to get her tuned up, fix oils leaks and anything else of concern while I drive her over the summer. Once fall/winter hits I would like to do a full repaint down to the metal. Special shout out to Arne as well as Craig from Camp 914 for the behind the scenes consults. Also shout out to John at Hayes European in Santa Cruz for the PPI! Wish me luck! ![]() |
![]() ![]() |
Cairo94507 |
![]()
Post
#2
|
Michael ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 10,318 Joined: 1-November 08 From: Auburn, CA Member No.: 9,712 Region Association: Northern California ![]() ![]() |
Assuming the problem is not as pointed out by Mark, if you are going to touch the motor, and you have the resources, I would really touch it. I would pull it and do a complete rebuild and take it to a 2056 but otherwise keep it essentially stock so it remains very reliable and trouble free.
That, of course, would be a great time to freshen the engine compartment, repair any rust issues in the engine compartment, send the tins out for powder coating, have the exhaust blasted and jet-hot coated, SS fuel lines if not already done, new clutch, etc. Yeah, it is a slippery slope. But for me, if it goes up on jack stands, I would want to get as much of the mechanical out of the way at that time as possible. Then once it goes back together it is just the cosmetics, suspension, paint, etc. Then again, you could just drive it and wait until you are ready to pull it apart. (IMG:style_emoticons/default/beerchug.gif) |
914_7T3 |
![]()
Post
#3
|
Please forgive me, I'm new to all of this! ![]() ![]() ![]() Group: Members Posts: 1,875 Joined: 3-April 17 From: Los Angeles, CA Member No.: 20,991 Region Association: Southern California ![]() ![]() |
Assuming the problem is not as pointed out by Mark, if you are going to touch the motor, and you have the resources, I would really touch it. I would pull it and do a complete rebuild and take it to a 2056 but otherwise keep it essentially stock so it remains very reliable and trouble free. That, of course, would be a great time to freshen the engine compartment, repair any rust issues in the engine compartment, send the tins out for powder coating, have the exhaust blasted and jet-hot coated, SS fuel lines if not already done, new clutch, etc. Yeah, it is a slippery slope. But for me, if it goes up on jack stands, I would want to get as much of the mechanical out of the way at that time as possible. Then once it goes back together it is just the cosmetics, suspension, paint, etc. Then again, you could just drive it and wait until you are ready to pull it apart. (IMG:style_emoticons/default/beerchug.gif) Reason why I am asking is that at first I was enamored with doing the 2056 from a specialty shop. Can't argue with the upgrade. However, I also have an old school air cooled specialist locally that can do it stock for literally half the cost in about two weeks. If it is top end only it would be about 30% of the cost of doing the 2056. The air cooled specialist works on VWs & 914s and has been working on my Beetle for 20 years and is in the same location for 50. I have no doubt he can do a great job so long as it is bone stock and I'm OK with preserving the originality. Truth be told I did a PCA run last month with all the 911 & Cayman types and couldn't keep up. So when my lease is up on the daily driver I will consider a pre-owned Cayman or 996. No need to worry about making the teener quicker at that point. |
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 10th May 2025 - 04:20 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |