 what is the best way to remove a ball joint without the tool? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tazz9924 |
 Jul 28 2017, 04:10 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 736 Joined: 31-May 15 From: Mooresville NC Member No.: 18,779 Region Association: None  |
as the title states what is the best way to remove the ball joint from the control arm with out the proper tool?
|
   |
 
|
  |
Replies
| rgalla9146 |
Jul 28 2017, 07:09 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 4,769 Joined: 23-November 05 From: Paramus NJ Member No.: 5,176 Region Association: None 
|
OOPS, I just checked at Baum tools.
It is now about $80. Pelican offers two $108. OR $57. It was $25. When I bought it. |
|
|
|
Posts in this topic
tazz9924 what is the best way to remove a ball joint without the tool? Jul 28 2017, 04:10 PM
fixer34
as the title states what is the best way to remov... Jul 28 2017, 04:30 PM theer Try heating the housing (with a torch) then hold o... Jul 28 2017, 04:34 PM Optimusglen He's wondering about the ball joint from the c... Jul 28 2017, 04:34 PM toolguy do you mean the steering tie rod to strut? Pickle... Jul 28 2017, 05:14 PM Mark Henry The round 4 slot nut on the bottom?
There's a... Jul 28 2017, 06:21 PM Mark Henry I think it's this one https://www.amazon.com/P... Jul 28 2017, 06:28 PM rgalla9146 The one that does the steering is a tie rod end.
... Jul 28 2017, 06:49 PM mepstein Buy the proper tools. The pickle fork is cheap. Th... Jul 28 2017, 06:59 PM Mitox Just buy the tool. As stated earlier they're ... Jul 28 2017, 06:59 PM porschetub Buy the tool,really not expensive,if you own a 914... Jul 28 2017, 07:08 PM Valy The tool won't get that crown nut out. Use a b... Jul 28 2017, 07:48 PM
mepstein
The tool won't get that crown nut out. Use a ... Jul 28 2017, 08:12 PM cary
The tool won't get that crown nut out. Use a... Jul 29 2017, 08:17 AM 914Sixer Make sure you soak the nut in PB Blaster overnight... Jul 28 2017, 08:21 PM mepstein We use a lot of liquid heat at the shop to remove ... Jul 28 2017, 08:41 PM tazz9924 i got in on and off real good with a pipe wrench a... Jul 29 2017, 02:01 AM frostyf I wanted to ask for some tips or advice on this to... Sep 15 2020, 09:37 PM VaccaRabite
I wanted to ask for some tips or advice on this t... Sep 16 2020, 06:26 AM mepstein I disagree with Zach. I’ve removed the ballpoint... Sep 16 2020, 06:26 AM frostyf
I disagree with Zach. I’ve removed the ballpoin... Sep 16 2020, 06:35 AM mepstein
I disagree with Zach. I’ve removed the ballpoi... Sep 16 2020, 01:27 PM VaccaRabite Sounds like there is a much better tool now then t... Sep 16 2020, 07:30 AM frostyf
Sounds like there is a much better tool now then ... Sep 16 2020, 10:20 AM 930cabman Just did this today, the tie rod end came off easy... Jan 30 2023, 05:27 PM r_towle Rent the tool… Jan 30 2023, 05:40 PM 930cabman
Rent the tool…
Round nut with 4 prongs? Jan 30 2023, 05:43 PM rhodyguy Bottom nut? Copious amounts of AeroKroil and air c... Jan 30 2023, 05:46 PM 930cabman Bottom nut came off easily with heat/pipe wrench. ... Jan 30 2023, 05:48 PM r_towle Oh THAT nut…
What he said, every time ^^^^^^ Jan 30 2023, 08:15 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st July 2025 - 12:48 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.