 Alternate shifters, Cable shifter |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Steve1956 |
 Jan 17 2023, 10:39 AM
Post
#1
|
|
Newbie  Group: Members Posts: 6 Joined: 4-November 22 From: Morocco,Indiana Member No.: 26,966 Region Association: None  |
Good morning everyone,anyone using a Boxster cable shifter or other similar?
My engine swap won't allow the use of stock shift linkage. Thx,,, |
   |
 
|
  |
Replies
| Lilchopshop |
Jan 19 2023, 02:47 PM
Post
#2
|
|
Member Group: Members Posts: 75 Joined: 17-February 20 From: New York Member No.: 23,932 Region Association: North East States |
The mechanism I built is for a subaru transmission (which has the shift rod at the rear of the tranny). It looks very similar to the one sold by Zero Decibel Motorsports (only theirs is prettier).
http://zerodecibelmotorsports.com/products...mechanism-5spd/ There's a couple of folks on here who have made cable mechanisms for the side shift and tail shift 914 transmissions. Here's one thread on the topic: http://www.914world.com/bbs2/index.php?showtopic=198714 By the way, I have two brand-new 6-foot long push-pull cables that I will sell to you for half of what they cost new. They were too short for my subaru transmission, but they might be just right for the side-shift location on the 914 tranny. Hope this helps! |
|
|
|
| Steve1956 |
Jan 20 2023, 12:47 PM
Post
#3
|
|
Newbie Group: Members Posts: 6 Joined: 4-November 22 From: Morocco,Indiana Member No.: 26,966 Region Association: None |
QUOTE(Lilchopshop @ Jan 19 2023, 03:47 PM)  The mechanism I built is for a subaru transmission (which has the shift rod at the rear of the tranny). It looks very similar to the one sold by Zero Decibel Motorsports (only theirs is prettier). http://zerodecibelmotorsports.com/products...mechanism-5spd/ There's a couple of folks on here who have made cable mechanisms for the side shift and tail shift 914 transmissions. Here's one thread on the topic: http://www.914world.com/bbs2/index.php?showtopic=198714 By the way, I have two brand-new 6-foot long push-pull cables that I will sell to you for half of what they cost new. They were too short for my subaru transmission, but they might be just right for the side-shift location on the 914 tranny. Hope this helps! I am assuming the cables are for Subaru shifter? I don't care about pretty,just functionality. What year, model suby? Good info! Thx. |
|
|
|
Posts in this topic
Steve1956 Alternate shifters Jan 17 2023, 10:39 AM
914werke :D Hold on let me find my crystal ball :shades2: ... Jan 17 2023, 11:50 AM tygaboy :agree: but I'll try and help anyway:
Yes, I... Jan 17 2023, 12:13 PM Lilchopshop I'm using a shifter from a Boxster with my Sub... Jan 17 2023, 01:55 PM Steve1956 I have a GM 3.1lt 60degree V6 installed with a ... Jan 19 2023, 01:18 PM
Lilchopshop
[quote name='Lilchopshop' post='3052303' date='Ja... Jan 26 2023, 10:40 AM Chris914n6 I bent the 914 rod to clear my Nissan engine or I ... Jan 21 2023, 02:09 AM Chris914n6 Found pics. Rear half is stock 914. Front half is ... Jan 25 2023, 03:28 PM 76-914 :blink: Jan 26 2023, 10:56 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 04:12 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.