60mm AFR Gauge - "Gauging" Interest |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
60mm AFR Gauge - "Gauging" Interest |
jbell959 |
Dec 4 2023, 10:42 AM
Post
#1
|
Newbie Group: Members Posts: 3 Joined: 2-May 21 From: CA Member No.: 25,505 Region Association: None |
As some of you may know, I build an 80mm custom AFR gauge as a clock replacement for 911s and recently someone asked me if it was possible to build a 60mm version. I was able to fit the main board and stepper movement in a 60mm case. This is just a prototype, but it does appear that with a little work, I could make these. It would require a 60mm temp or volt gauge as the donor to get the case, face, and needle. I don't yet have an estimate on the cost, but I wanted to see if there would be any interest before I spend more time on it.
Like all of my other AFR solutions, this gauge would work with most wideband controllers including but not limited to AEM, Innovate, PLX, and 14Point7. Sorry for the blurry picture! Attached thumbnail(s) |
Montreal914 |
Dec 4 2023, 05:45 PM
Post
#2
|
Senior Member Group: Members Posts: 1,572 Joined: 8-August 10 From: Claremont, CA Member No.: 12,023 Region Association: Southern California |
I bought something like this for less than $15 (thanks to @GregAmy ) to use it with my microsquirt conversion (when I get to it... (IMG:style_emoticons/default/rolleyes.gif) ).
https://www.adafruit.com/product/1778?gad_s...uBoCWJwQAvD_BwE I think there are a few like this around. One would have to ensure it is temperature compensated (which I believe mine is). Now how to convert the 0-5V output in something that can drive a VDO gauge? (IMG:style_emoticons/default/idea.gif) Clearly the volt gauge uses the 8-16V range but how precisely? Then how to precisely bump up the interesting portion (250-450F) of the 0-5V output into 8-16 V for the VDO Volt Meter. That would be a question for the electronic gurus. (IMG:style_emoticons/default/smile.gif) Or, is the movement of the typical VDO gauges low voltage, something close to 0-5V? (IMG:style_emoticons/default/confused24.gif) One thing is sure, a good and precise 60mm CHT gauge with the same design as the other center console gauge would be a high seller. The larger the scale the better (like the MBZ span). Silver dot hand for me please! (IMG:style_emoticons/default/smile.gif) |
GregAmy |
Dec 4 2023, 10:52 PM
Post
#3
|
Advanced Member Group: Members Posts: 2,311 Joined: 22-February 13 From: Middletown CT Member No.: 15,565 Region Association: North East States |
... I bought something like this for less than $15...to use it with my microsquirt conversion (when I get to it... (IMG:style_emoticons/default/rolleyes.gif) ). Yeah, where is that, brother? Get on this, Lewis! The gauge? I like this idea. A lot. As a racer...it's hard to correlate throttle, RPM, and load with an AFR gauge and use it as a tool to decide jetting or tuning; you're spending way more time just trying to not drive into something. The best way is data acq to review after, but not all of us have that tool. I could see using this as a crowbar binary determination that when I'm WOT at 5000 RPM and looking down my AFR is too lean (or fat). And that would work with macro carb tuning. But with EFI it's not fine enough. But honestly, this is kinda freakin cool for most of us. I'd put one in just 'cause I could. And point to it as I'm driving along. GA |
Lo-Fi Version | Time is now: 2nd June 2024 - 05:47 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |