 Tool needed from someone local, Someone should have one of these close by |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| skline |
 Apr 24 2007, 12:14 AM
Post
#1
|
|
Born to Drive  Group: Members Posts: 7,910 Joined: 26-December 02 From: Costa Mesa, CA Member No.: 17 Region Association: Southern California  |
I am taking the front end apart and for some reason, I cannot find my tie rod splitter tool, the one to remove the tie rods from the spindle, does anyone local have one I can borrow to get this thing apart? I could come get it if it is not too far away.
|
   |
 
|
  |
Replies
| skline |
Apr 27 2007, 04:19 PM
Post
#2
|
|
Born to Drive Group: Members Posts: 7,910 Joined: 26-December 02 From: Costa Mesa, CA Member No.: 17 Region Association: Southern California |
Special thanks to Elliot for stopping by today with his little tool (IMG:style_emoticons/default/smile.gif)
I was only able to get one side off with it however but it was something. I went to Kragen and they wanted $22.00 to rent the tool that I would get it back when I returned it or I could just buy the tool I needed for $10.00, since they didnt have the rental one there, I just bought the tool, came home and about 10 whacks of the hammer, I got it off. I tell you, having the right tools, makes a whole world of difference. This is what you need to get the tie rods off. See pictures for those who are not so literate Attached image(s)  
|
|
|
|
Posts in this topic
skline Tool needed from someone local Apr 24 2007, 12:14 AM
r_towle turn wheel so you can get to the back of the spind... Apr 24 2007, 12:18 AM skline Nub??? It is a Carrera front end, I tried beating ... Apr 24 2007, 12:20 AM r_towle there is a flat spot on the centerline of the arm ... Apr 24 2007, 12:25 AM Lou W I have a fork type tool that I think would work in... Apr 24 2007, 12:27 AM skline Ok, I will give it a try....... :smash: Apr 24 2007, 12:28 AM Twystd1 Scott,
I AM ON M,Y WAY OVER...
All I need is a b... Apr 24 2007, 12:30 AM skline Well, I tried it, no avail.....
Clayton just call... Apr 24 2007, 12:32 AM
skline
Well, I tried it, no avail.....
Clayton just cal... Apr 24 2007, 01:26 AM jd74914 Could you post a picture showing what Rich is talk... Apr 24 2007, 09:14 AM Aaron Cox pickle fork? Apr 24 2007, 09:22 AM Lou W
pickle fork?
Heh heh... He said pickle fork. :... Apr 25 2007, 06:06 PM bd1308 yes! its the atomic bomb of automotive tooling... Apr 24 2007, 09:24 AM Justinp71
I am taking the front end apart and for some reas... Apr 24 2007, 10:35 AM r_towle Tie rod end pic,
Just above the thumb in this pict... Apr 24 2007, 11:47 AM Aaron Cox back the nut off, and flip it over....
then beat ... Apr 24 2007, 12:15 PM Elliot Cannon Scott,
Is this the tool you need? Apr 24 2007, 05:10 PM Aaron Cox thats a neat little tool! Apr 24 2007, 05:37 PM skline That might work Elliot, did you have it or are you... Apr 24 2007, 08:05 PM Elliot Cannon
That might work Elliot, did you have it or are yo... Apr 25 2007, 05:40 PM skline
That might work Elliot, did you have it or are y... Apr 26 2007, 09:34 PM Aaron Cox you coulda spent 5 bucks in gas and borrowed my pi... Apr 27 2007, 06:27 PM skline
you coulda spent 5 bucks in gas and borrowed my p... Apr 27 2007, 11:41 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th June 2024 - 07:26 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.