 Got a lot done today, but......, Or am I fuched? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| KaptKaos |
 Oct 7 2007, 08:53 PM
Post
#1
|
|
Family  Group: Members Posts: 4,009 Joined: 23-April 03 From: Near Wausau Member No.: 607 Region Association: Upper MidWest  |
So I have the HEs installed and the muffler too.
I went top side to install the intake manifolds. I got the driver side in, but when I went to do the passenger side, I got this:  That silvery stuff on the intake stud is aluminum. I didn't over torque it, it never got tight at all. So the question is, am I fuched or can I relatively easily fix this? TIA |
   |
 
|
  |
Replies
| BMartin914 |
Oct 8 2007, 07:16 PM
Post
#2
|
|
||| Group: Members Posts: 1,408 Joined: 30-May 04 From: Oregon Member No.: 2,128 Region Association: Pacific Northwest |
Yes. 8x1.25mm kit. It has all the bits needed to get the job done. 4 steps and you're good as new. Just don't forget to clean out the hole very thoroughly of all metal shavings. They can compact in the bottom of the hole sometimes and cause problems (even if you are working upside down). Carb cleaner and shop air is waht I use.
|
|
|
|
Posts in this topic
KaptKaos Got a lot done today, but...... Oct 7 2007, 08:53 PM
Aaron Cox helicoil or timesert.
Isnt that hard... but will... Oct 7 2007, 09:27 PM SLITS Do a helicoil if your can get a drill motor with b... Oct 7 2007, 09:37 PM
BMartin914
Kits are available at parts stores.
I prefer ... Oct 7 2007, 09:47 PM Twystd1 DO NOT DRILL TOO DEEP.
Or you will be seriously F... Oct 7 2007, 09:58 PM Krieger914 I have had great luck in a 912 E using 3 time cert... Oct 7 2007, 10:09 PM Twystd1 Locktite red won't work in his application. Th... Oct 7 2007, 10:34 PM Aaron Cox
.....
I dunno.. Sean. let me know if'n ya nee... Oct 7 2007, 10:52 PM Twystd1 Aaron......
I meant Joe.....
I was trying to be ... Oct 7 2007, 11:01 PM KaptKaos No worries Clayton.
I'm just pissed because ... Oct 8 2007, 12:19 AM KaptKaos This may sound like a stupid question, but if I us... Oct 8 2007, 12:25 AM KaptKaos Ok, here is the timesert site. Very nice site, he... Oct 8 2007, 12:58 AM Gint I prefer timeserts myself. Oct 8 2007, 11:19 AM jk76.914 When I did a timesert for an exhaust stud, I drill... Oct 8 2007, 11:37 AM KaptKaos I'll likely do the timesert, but I can't t... Oct 8 2007, 11:39 AM jk76.914
I'll likely do the timesert, but I can't ... Oct 8 2007, 07:07 PM Demick Surprised nobody mentioned JBWeld. This is a stud... Oct 8 2007, 11:55 AM KaptKaos
Surprised nobody mentioned JBWeld. This is a stu... Oct 8 2007, 12:42 PM Grimstead :(
I'm no help but here is a afternoon :bump... Oct 8 2007, 06:41 PM jk76.914 OOPS! I was thinking exhaust. You DON'T ... Oct 8 2007, 07:08 PM Headrage Joe,
Sent you a PM.
If it doesn't work I... Oct 8 2007, 07:18 PM swood
Joe,
Sent you a PM.
If it doesn't work I... Oct 8 2007, 08:05 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 07:04 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.