 Losing oil, out of hole near cyclingder three |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| turnaround89 |
 Oct 20 2008, 04:44 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 671 Joined: 17-May 08 From: Rockford, Illinois Member No.: 9,067 Region Association: Upper MidWest  |
Everytime i drive my car, there is always a little pool of oil that collects behind a little hole by cylinder 3, the oil collects on top of the cooling tins in the back corner of the car. The hole is next to the nut that holds the intake on, its about .5inch diameter or smaller(didn't measure it just guessing) What can i do to stop this oil issue? I also noticed this same hole is on the opposite side of the engine but instead of being behind the intake it is in front of the intake by cylinder 2, no oil comes out of that hole. Maybe the oil isn't coming out of the holes but somewhere else. All i know is that oil collects by cylinder 3 on top of the cooling tins. thanks everybody!! help my car not spew oil, my dad hates oil spots when i pull into the driveway
|
   |
 
|
Posts in this topic
turnaround89 Losing oil Oct 20 2008, 04:44 PM
southernmost914 Sounds like your missing your rocker/head vent hos... Oct 20 2008, 04:49 PM turnaround89 yes, the PO sold the orig 2.0 that was in the car ... Oct 20 2008, 04:55 PM Doug Leggins I have had oil in the same place. My issue turned ... Oct 20 2008, 04:56 PM jsayre914 what kinda oil are you using?? I had the same prob... Oct 20 2008, 04:59 PM turnaround89 I don't know what oil is in the car at the mom... Oct 20 2008, 05:03 PM southernmost914 I'm pretty sure your missing a crankcase breat... Oct 20 2008, 05:09 PM turnaround89 Would the ones from the heads go into the breathe... Oct 20 2008, 05:25 PM southernmost914 Those should have hoses going to a aftermarket bre... Oct 20 2008, 05:29 PM turnaround89 was there ever a stock breather system? Where can... Oct 20 2008, 05:30 PM r_towle You have two choices.
You can go get two brass 90 ... Oct 20 2008, 05:34 PM turnaround89 Do i have to put the fitting onto the top of the a... Oct 20 2008, 05:52 PM
southernmost914
Do i have to put the fitting onto the top of the ... Oct 20 2008, 05:56 PM Grelber I had a breather problem too, and my engine guy sa... Oct 20 2008, 06:11 PM SirAndy On a FI motor, those each have a hose going to the... Oct 20 2008, 07:09 PM turnaround89 SirAndy, on your setup your middle line that goes ... Oct 20 2008, 08:10 PM SirAndy
Why will the oil go into the catch can rather tha... Oct 20 2008, 08:42 PM turnaround89 Thanks everybody, 2moro i will drill the other hol... Oct 20 2008, 09:27 PM scottb a look in the vendor section shows our very own ch... Oct 21 2008, 04:57 AM turnaround89 Just want to say thanks to everybody's help on... Oct 22 2008, 12:58 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th June 2024 - 04:10 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.