 Where does this bushing go?, rear shift rod bushing |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| Hammy |
 May 6 2006, 08:31 PM
Post
#1
|
|
mr. Wonderful  Group: Members Posts: 1,826 Joined: 20-October 04 From: Columbia, California Member No.: 2,978 Region Association: Northern California  |
I bought new bushings and can't seem to find where this one goes.
Picture of it here. I know there's a Pelican article telling where it goes but I still can't figure it out, and the picture they have isn't much help. Can anyone tell me or have a diagram? Much appreciated. |
   |
 
|
| SirAndy |
May 6 2006, 08:34 PM
Post
#2
|
|
Resident German Group: Admin Posts: 41,633 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
QUOTE(Hammy @ May 6 2006, 07:31 PM)  I bought new bushings and can't seem to find where this one goes. Picture of it here. I know there's a Pelican article telling where it goes but I still can't figure it out, and the picture they have isn't much help. Can anyone tell me or have a diagram? Much appreciated. looks like the one that goes on the console on the sideshifter. basically, where the end of the shiftrod meets the transmission (on a sideshifter), the rod passes through a hole on the console right before the coupler. bushing goes in that hole ... (IMG:style_emoticons/default/smile.gif) Andy |
|
|
|
| Joe Bob |
May 6 2006, 08:36 PM
Post
#3
|
|
Retired admin, banned a few times Group: Members Posts: 17,427 Joined: 24-December 02 From: Boulder CO Member No.: 5 Region Association: None |
Yupz....
|
|
|
|
| Hammy |
May 6 2006, 11:16 PM
Post
#4
|
|
mr. Wonderful Group: Members Posts: 1,826 Joined: 20-October 04 From: Columbia, California Member No.: 2,978 Region Association: Northern California |
Thanks dudez (IMG:style_emoticons/default/aktion035.gif)
|
|
|
|
| jsteele22 |
May 7 2006, 03:37 PM
Post
#5
|
|
Senior Member Group: Members Posts: 727 Joined: 24-August 05 From: Colorado Springs, CO Member No.: 4,653 |
Anybody ever installed that bushing without hours of beating the crap out of it with every tool imaginable, and then whittling it down to fit ? Just curious.
|
|
|
|
| McMark |
May 7 2006, 03:39 PM
Post
#6
|
|
914 Freak! Group: Retired Admin Posts: 20,179 Joined: 13-March 03 From: Grand Rapids, MI Member No.: 419 Region Association: None |
Yeah. (IMG:style_emoticons/default/confused24.gif) Boil some water (remove from heat) and drop it in for 30 seconds. Should be more pliable at that point. But I can't remember ever having a problem.
|
|
|
|
| SirAndy |
May 7 2006, 08:39 PM
Post
#7
|
|
Resident German Group: Admin Posts: 41,633 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
QUOTE(McMark @ May 7 2006, 02:39 PM) Yeah. (IMG:style_emoticons/default/confused24.gif) Boil some water (remove from heat) and drop it in for 30 seconds. Should be more pliable at that point. But I can't remember ever having a problem. cup of water, throw it in, microwave for a minute or two. voila ... (IMG:style_emoticons/default/smile.gif) Andy |
|
|
|
| jsteele22 |
May 7 2006, 10:53 PM
Post
#8
|
|
Senior Member Group: Members Posts: 727 Joined: 24-August 05 From: Colorado Springs, CO Member No.: 4,653 |
Great ! Maybe some day I'll buy another one. NOT ! p.s. Has anyone said "NOT" like that in the past ten years ? |
|
|
|
| Twystd1 |
May 7 2006, 11:01 PM
Post
#9
|
|
You don't want to know... really..... Group: Members Posts: 2,514 Joined: 12-September 04 From: Newport Beach, California Member No.: 2,743 |
"NOT"
|
|
|
|
| Tobra |
May 7 2006, 11:52 PM
Post
#10
|
|
Senior Member Group: Members Posts: 1,453 Joined: 22-August 05 From: Sacramento, CA Member No.: 4,634 |
Mine was easy, heated snapped in front to back, no problem, whole job was really straightforward and simple
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th May 2024 - 07:22 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.