914outlaw
Oct 14 2013, 01:40 AM
Updated old post 8/24/15
Cut up most of the car.
Sail panels left and right $70 each
Suspension console Driver side $100
Rear Sway Bar $100
Driver side quarter panel $100
Passenger side quarter panel $50. There is some bondo from a previous dent repair toward the front.
Driver door $50
Trunk lid $100
Heater blower fan $50
Firewall $100
More pictures
Link to more pictures on photobucketAll prices are Best Offer + shipping. PM me if you're interested. I'm located near Trenton, NJ
914outlaw
Oct 14 2013, 10:27 AM
I'll try to post some more pix tomorrow.
jimkelly
Oct 15 2013, 08:54 AM
mostly curious ...
is rear bumper dent free?
are doors rust free, especially at bottoms?
jim
Vysoc
Oct 15 2013, 05:02 PM
PM Sent.
Vysoc
914outlaw
Oct 16 2013, 05:58 PM
914outlaw
Oct 16 2013, 06:07 PM
QUOTE(jimkelly @ Oct 15 2013, 10:54 AM)
mostly curious ...
is rear bumper dent free?
are doors rust free, especially at bottoms?
jim
Hey Jim,
The rear bumper is dent free however on the bottom right there is about a quarter size (give or take) spot where the chrome is flaking. The driver side door has visible rust at the bottom. The passenger side looks alot better but I couldn't look more closely because I ran out of daylight. I tried to take a close up picture of everything. This weekend I can take better pictures.
Rear bumper
Passenger door
Driver side door
914outlaw
Oct 16 2013, 06:22 PM
All pms replied to.
914outlaw
Oct 18 2013, 07:36 PM
Not much interest in body panels, so I'm not cutting it up this weekend. I think I'm just going to start stripping down what's left and post what I'm not keeping. I'm just trying to partially fund my purchase of a scissor lift for my winter project and make room in my driveway. So feel free to make reasonable offers. I'll post some pictures with my prices tomorrow. If someone is interested in a specific part, PM me so I can take it off first and post it. I don't think I'll be able to pull everything off tomorrow.
Thanks for reading my ad and let me know if there is anything you need.
Vysoc
Oct 23 2013, 02:28 PM
QUOTE(dpires914 @ Oct 18 2013, 09:36 PM)
Not much interest in body panels, so I'm not cutting it up this weekend. I think I'm just going to start stripping down what's left and post what I'm not keeping. I'm just trying to partially fund my purchase of a scissor lift for my winter project and make room in my driveway. So feel free to make reasonable offers. I'll post some pictures with my prices tomorrow. If someone is interested in a specific part, PM me so I can take it off first and post it. I don't think I'll be able to pull everything off tomorrow.
Thanks for reading my ad and let me know if there is anything you need.
Dave,
I sent you a PM about the area around the Master Cylinder, here are 4 photos of what I am looking for, my last PM had an offer for the piece.
Thank you,
Vysoc
Click to view attachmentClick to view attachmentClick to view attachmentClick to view attachment
KENNY
Oct 23 2013, 04:18 PM
Looking for a rear left brake light . Is the one in the car in good shape and how much
Trekkor
Oct 23 2013, 04:53 PM
I'm interested in the entire firewall hump.
KT
Vysoc
Oct 26 2013, 04:56 PM
Hey Dave,
Are you still there?
How about a response?
Just saying?
Vysoc
914outlaw
Oct 26 2013, 07:17 PM
QUOTE(Vysoc @ Oct 26 2013, 06:56 PM)
Hey Dave,
Are you still there?
How about a response?
Just saying?
Vysoc
Sorry. PM replied.
914outlaw
Oct 26 2013, 07:26 PM
QUOTE(Trekkor @ Oct 23 2013, 06:53 PM)
I'm interested in the entire firewall hump.
KT
PM sent
JeffBowlsby
Oct 26 2013, 08:00 PM
What condition is the chassis harness in? I would be intrested in it if its not cut or damaged. Email me please.
sluggosteam
Oct 28 2013, 05:19 AM
How much for the nose piece that front bumper mounts to??
Covvers
Oct 28 2013, 05:39 AM
Is this section of the driver's front quarter panel in any better condition than mine? And if so, how much posted to Melbourne, Australia?
Click to view attachment Andrew
shuie
Oct 28 2013, 08:02 AM
I can use the rear latch panel whenever you do decide to cut the car up.
chads74
Oct 28 2013, 09:00 AM
PM sent
914outlaw
Oct 28 2013, 10:59 PM
QUOTE(sluggosteam @ Oct 28 2013, 07:19 AM)
How much for the nose piece that front bumper mounts to??
The nose piece is pretty rusted on the far right and far left. I think the middle part is ok. Look at my picture to the right of the fog light.
if you still want it. I'll take $40 obo + shipping.
914outlaw
Oct 28 2013, 11:05 PM
QUOTE(Covvers @ Oct 28 2013, 07:39 AM)
Is this section of the driver's front quarter panel in any better condition than mine? And if so, how much posted to Melbourne, Australia?
Click to view attachment Andrew
I think it is. I cab inspect it better on Saturday. I'll post a close up picture. I would like to sell the fender as a whole piece if I can since it's a pretty straight piece.
I'm thinking of using it on my project if no one takes it.
914outlaw
Oct 28 2013, 11:05 PM
QUOTE(chads74 @ Oct 28 2013, 11:00 AM)
PM sent
All PMs replied to.
Covvers
Oct 29 2013, 12:54 AM
QUOTE(dpires914 @ Oct 29 2013, 04:05 PM)
QUOTE(Covvers @ Oct 28 2013, 07:39 AM)
Is this section of the driver's front quarter panel in any better condition than mine? And if so, how much posted to Melbourne, Australia?
Click to view attachment Andrew
I think it is. I cab inspect it better on Saturday. I'll post a close up picture. I would like to sell the fender as a whole piece if I can since it's a pretty straight piece.
I'm thinking of using it on my project if no one takes it.
That's ok. I *would* take the whole thing, but the postage wouldn't make it worthwhile even if you were giving it away for free.
sluggosteam
Oct 29 2013, 03:40 PM
QUOTE(dpires914 @ Oct 28 2013, 10:59 PM)
QUOTE(sluggosteam @ Oct 28 2013, 07:19 AM)
How much for the nose piece that front bumper mounts to??
The nose piece is pretty rusted on the far right and far left. I think the middle part is ok. Look at my picture to the right of the fog light.
if you still want it. I'll take $40 obo + shipping.
Yea thanks, now that I looked a little closer its as bad as mine.
914outlaw
Nov 1 2013, 10:40 AM
All pms replied to.
liebe
Nov 3 2013, 07:03 PM
QUOTE(dpires914 @ Nov 1 2013, 05:40 PM)
All pms replied to.
How much for the fog lights ? shipping to Houston.
914outlaw
Nov 15 2013, 09:50 PM
QUOTE(liebe @ Nov 3 2013, 08:03 PM)
QUOTE(dpires914 @ Nov 1 2013, 05:40 PM)
All pms replied to.
How much for the fog lights ? shipping to Houston.
PM replied to.
Pictures and prices added to Post #1.
liebe
Nov 16 2013, 03:17 AM
QUOTE(dpires914 @ Nov 16 2013, 04:50 AM)
QUOTE(liebe @ Nov 3 2013, 08:03 PM)
QUOTE(dpires914 @ Nov 1 2013, 05:40 PM)
All pms replied to.
How much for the fog lights ? shipping to Houston.
PM replied to.
Pictures and prices added to Post #1.
David, responded by PM. Also want the front round rubber covers, between fog lights please.
rmdinmd
Nov 16 2013, 10:25 AM
how much for the heater parts, don't need the motor but need every thing but the HE and blowerm moter. pm me the rice and payment meathod
rick
luka
Nov 21 2013, 10:14 PM
Hi. Is the quarter left hand side door glass (ie, the small trianglar quarter glass and rubber on forward section of door) in good condition ie.without scratchs.
would you sent to australia Melbourne?
email address; domenicluka@hotmail.com
Thanks
Domenic Luka
luka
Nov 21 2013, 10:22 PM
Hi.
What condition is the rear corner sections (the left and right cornors) inside the rear boot compartment just in front of the rear brake lights like?
Would you sent to australia Melbourne?
email address; domenicluka@hotmail.com
Thanks
Domenic Luka
euro911
Nov 22 2013, 12:40 AM
How's the rear targa bar pad?
914outlaw
Nov 22 2013, 06:40 PM
QUOTE(luka @ Nov 21 2013, 11:22 PM)
Hi.
What condition is the rear corner sections (the left and right cornors) inside the rear boot compartment just in front of the rear brake lights like?
Would you sent to australia Melbourne?
email address; domenicluka@hotmail.com
Thanks
Domenic Luka
Yes, I can send to Australia.
I'll post some pictures by tomorrow.
914outlaw
Nov 22 2013, 06:42 PM
QUOTE(euro911 @ Nov 22 2013, 01:40 AM)
How's the rear targa bar pad?
I think there might be a few cracks. I'll take a couple of pictures and post.
914outlaw
Nov 24 2013, 12:16 AM
Harpo
Nov 24 2013, 11:40 AM
How about the plugs that hold the floor mats in place?
Thanks
DAvid
914outlaw
Nov 24 2013, 09:00 PM
QUOTE(Harpo @ Nov 24 2013, 12:40 PM)
How about the plugs that hold the floor mats in place?
Thanks
DAvid
Not sure. Here is a picture of the floors.
ChrisG914
Dec 8 2013, 02:48 PM
Interested in the seats if you still have them. In NJ and can pickup. Pm o r email me.
Thanks - Chris
wgoldberg
Dec 9 2013, 12:49 AM
not smooth with 914 world. I need parts but can we talk on the phone or email. Thanks, bill email is abelgian@msn.com
914outlaw
Jan 14 2014, 09:06 PM
Selling whole car now.
See post#1
914outlaw
Jan 27 2014, 06:44 PM
I've changed my mind on cutting this up and am selling it as a roller. $500 obo.
It has straight and solid fenders.
Link to more pictures on photobucketThings that are gone.
Riviera wheels
Steering wheel
front bumper
speaker grills
tail lights
PM me if you're interested. I'm located near Trenton, NJ
914outlaw
Feb 16 2014, 10:59 PM
Crappy winter
914outlaw
Mar 13 2014, 08:19 PM
Still a Crappy winter
914outlaw
May 2 2014, 05:02 PM
Bump for whole car or parts.
Oxen914
May 3 2014, 06:43 AM
How much do you want for the engine lid?
914outlaw
May 3 2014, 09:28 AM
QUOTE(Oxen914 @ May 3 2014, 08:43 AM)
How much do you want for the engine lid?
Asking $100 for the lid. obo
914outlaw
May 6 2014, 10:03 PM
Would like to sell this weekend. I might just have to scrap it.
914outlaw
May 29 2014, 09:43 AM
QUOTE(dpires914 @ May 7 2014, 12:03 AM)
Would like to sell this weekend. I might just have to scrap it.
914outlaw
Jun 10 2014, 12:29 AM
QUOTE(dpires914 @ May 29 2014, 11:43 AM)
QUOTE(dpires914 @ May 7 2014, 12:03 AM)
Would like to sell this weekend. I might just have to scrap it.
type11969
Oct 13 2014, 08:36 PM
May be too late - but did you scrap this? Might be interested in the pass rear fender, maybe both. Have sawzall, will travel. Let me know.
Chris
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.