Click on the link in my signature to place an order.

The diaphragm stampings should be here in less than 2 weeks, so I think the repair kits will be ready to ship before this month's end.
The Tuning Kits would be ready by now but my machinist seems to have flaked out. (see other thread)

Diaphragm Kit Price goes up $12 once they're in stock.

Chris,

Count me in for one. Thanks for doing this!

Jerry

Order HERE!

Paid

Repair and tune kit

Paid for repair kit.

We're getting real close!
I had diaphragm samples in hand yesterday, swaged a hub onto one, and did a trial assembly of an MPS with it.
The rest were sent back for heat treat today, along with a couple minor "adjustments" for the production run.

The full load stop screws are being shipped. (At least I think they are. I've been having trouble with this vendor)

Here's a pic of the first sample diaphragm and hub pieces.

Click to view attachment

:drool:

We're one step closer today. The stop screws have arrived.
Click to view attachment

Uses an 8mm Hex driver to install & adjust
Click to view attachment

Fits in the cover perfectly, after a good cleaning of the threaded hole.
Click to view attachment

The adjusting tools fit as intended.
Click to view attachment

Good to go.
Click to view attachment

Complete Tuning Kit
Click to view attachment

Very nice!

This is a historic reproduction of an NLA part.

Five years from now it will be a thing of legend and hard to find again.

Better get one now for each of your cars that need one.

John

I bought 2 I think, and went Subie to boot;-)

Awesome job Mr. Foley!

...we're not worthy, we're not worthy, etc., etc.;-)

Thx again for doing this for me . Just kidding. This will be my present this year. ps Will you let us know when you ship so that I can threaten my alcoholic mailman ahead of time. Otherwise, it could end up in in some other persons mailbox; again. Better yet, I'll pay the difference if you would ship it insured. I'm not shitting you, this guy belongs in a Chevy Chase movie.

This is what I've been waiting for!
Click to view attachment

...and the first re-production diaphragm, hot off the press:
Click to view attachment

awesome !


it is amazing what you and all of the vendors here make
amazing that parts like this can be produced for these old cars
brant

I guess your going to be shipping soon and bill us too?

I will be shipping a few of the earliest orders this evening, and more tomorrow.
Billing? I'm filling pre-paid orders right now.
If you haven't ordered yet, and want one soon, I suggest you follow the link in my signature to make your purchase.

Looks great Chris! Thanks for your work on this.

Now we need some of our MPS tuners to post some prices for the flood of new business coming.

Just got an email shipping notice from USPS that Racer Chris has sent me a Christmas present. There is a problem though, my '70 1.7 is currently in pieces scattered all over the garage and into the basement. Maybe by spring thaw I'll get to the MPS.

Thanks Chris.

Olin

Hoo! I received the shipping notice also. Sure my car doesn't have doors on it, but I have the O2 sensor and gauge all hooked up. At long last I'll be able to repair one of my lousy MPS units.

My holiday plans are now set.

As of today, the first 20 orders have been shipped.
(I ran out of Small Priority boxes.)

Instructions aren't written yet but I have taken pictures to write about.
I plan to email the instructions as soon as they're ready.

See, there really IS a santa claus! Those look great Chris!!

Yep, received my awesome update from CFR!!!

Thanks Chris, you are a true gentleman, and not so bad a mechanic

Now, all I gotta do is wait to see if Santa can fit a slightly used 2.0 down the chimney for free, or figure where this mounts on my Subie 2.5

Sold my other 4 motors

Hang onto the kit Dave, its destined to become a valuable NOS item someday.

...
or, like most of us, you'll buy another 914 sooner rather than later, and the mps will need to be serviced.

Sweet! Just got my shipping notice. Thx again, Chris.

Chris,
I received my kit on Monday just in time for my Christmas Stocking gift. Everything looked good and thanks for your committment to this MPS issue.

BTW: Just asking??/ Is there anyone (Bowsley, Bleyseng, Chris) out there who will calibrate and rebuild our MPS's with your kit & my spare MPS??? I would be willing to spend $$ to have someone rebuild my MPS & calibrate with the build specs on my motor for a fee-$$$. Anyone out there???
Tom

Adjusting one to stock specs is not to hard with a quality inductance meter. If the motor is a custom build though you will most likley need to tune it and possibly other things on the motor itself, i doubt anyone has enough data to set one just from build specs.

The parts and tools arrived today - top notch Chris!

I heard from Jeff Bowlsby yesterday. His order went out with the first batch.
He already installed one, set it up, and ran it in his car briefly.
According to his preliminary tests its right on the money!

I preorder and never reviewed my credit card bill for payment..I received your USPS email notification last week of shipment.
Thanks- free bump

Chris,

arrived safe and sound
Nice looking piece and kit
really nice

brant

Ordered mine yesterday.

Hey Chris. I got mine the other day. Very nice product! Thank you for making these. I bought this as a back up for the new MPS I bought a few years back. It may be a while until I use this part. If that is the case I am going to want to use new o-rings. Can you please give use the specs for those o-rings to make it easier to replace? Thank you.

Chris - are you still in production?

I bought another 300 stampings last year after selling out the first batch.

Hi Chris, are you still in production for the MPS D-Jet diaphragm?

You did a great job! Hope you haven't discontinued :-)

@MB107_IT You can order it, and lots of other indispensable things, on Chris' website -- Tangerine Racing.
http://www.tangerineracing.com/mpsdiaphragm.htm